Samsung Galaxy Tab S2 9.7 T818WVLS1BRD3
SM-T818W 1 country Android 7.0 (Nougat)

Samsung Galaxy Tab S2 9.7 T818WVLS1BRD3 Firmware

Samsung Galaxy Tab S2 9.7 T818WVLS1BRD3 is an Android 7.0 (Nougat) firmware for Canada (BMC, FMC, KDO, MTA, RWC, TLS, VMC, VTR, XAC). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build T818WVLS1BRA1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-T818W is available: T818WVLS4BTI2.

Download firmware
9.0/10 (458)39,188 times
Android 7.0 (Nougat)
OS Version
2018-04-27
Build Date
1
Countries
9
CSC codes
1
Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Tab S2 9.7 use bootloader binary 4 (latest: T818WVLS4BTI2). If your device already runs binary 4, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: T818WVLS1BRD3
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-T818W
    BMC, FMC, KDO, MTA, RWC, TLS, VMC, VTR, XAC Canada
    		T818WOYA1BRD3 2018-05-14 2.031 GiB
    SM-T818W_1_20201015145204_l3sh027982_fac.zip
    		Download

    No matching downloads

    How to flash T818WVLS1BRD3

    • T818WVLS1BRD3 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of T818WVLS1BRD3 by region

    Samsung released this build in all regions (9) on the same day, May 14, 2018.

    Frequently Asked Questions

    T818WVLS1BRD3 is Android 7.0 (Nougat) firmware for Samsung Galaxy Tab S2 9.7, released for Canada (BMC, FMC, KDO, MTA, RWC, TLS, VMC, VTR, XAC). Samsung built it on 2018-04-27.

    No. A newer build for SM-T818W is available: T818WVLS4BTI2. Install it instead of T818WVLS1BRD3 unless you need this exact version. The previous build was T818WVLS1BRA1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 2.031 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Tab S2 9.7 must be on bootloader binary 1 or lower.

    This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy Tab S2 9.7 running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 5 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Tab S2 9.7

    No changelog details available.

    · The security of your device has been improved.

    No changelog details available.
    Model firmware by region