Samsung Galaxy Tab S4 T837VVRU4BTA4
SM-T837V 1 country Android 9 (Oreo)

Samsung Galaxy Tab S4 T837VVRU4BTA4 Firmware

Samsung Galaxy Tab S4 T837VVRU4BTA4 is an Android 9 (Oreo) firmware for United States (VZW). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build T837VVRS3BSI1: bootloader binary raised from 3 to 4, so after installing it there is no way back to older builds. A newer build for SM-T837V is available: T837VVRS6CVE2.

Download firmware
9.1/10 (458)4,323 times
Android 9 (Oreo)
OS Version
2020-01-21
Build Date
1
Countries
1
CSC codes
4
Bootloader binary

Bootloader binary 4. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Tab S4 use bootloader binary 6 (latest: T837VVRS6CVE2). If your device already runs binary 6, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: T837VVRU4BTA4
    ModelRegionCSC VersionSizeFile nameDownload
    SM-T837V
    VZW United States
    		T837V4BTA4 — — Download

    No matching downloads

    How to flash T837VVRU4BTA4

    • T837VVRU4BTA4 has bootloader binary 4. Your device must run binary 4 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Display diagonal26.7 cm (10.5")
    • Display resolution2560 x 1600 pixels
    • Display technologySuper AMOLED
    • Rear camera resolution13 MP
    • Front camera resolution8 MP
    • Wi-Fi standardWi-Fi 5 (802.11ac)
    • Weight483 g

    Specifications of SM-T837, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    T837VVRU4BTA4 is Android 9 (Oreo) firmware for Samsung Galaxy Tab S4, released for United States (VZW). Samsung built it on 2020-01-21.

    No. A newer build for SM-T837V is available: T837VVRS6CVE2. Install it instead of T837VVRU4BTA4 unless you need this exact version. The previous build was T837VVRS3BSI1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Tab S4 must be on bootloader binary 4 or lower.

    This build uses bootloader binary 4. It can be flashed on a Samsung Galaxy Tab S4 running binary 4 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 4 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Tab S4

    No changelog details available.
    Model firmware by region