Samsung Galaxy A01 A015VVRU2ATG3
SM-A015V 1 country Android 10

Samsung Galaxy A01 A015VVRU2ATG3 Firmware

Samsung Galaxy A01 A015VVRU2ATG3 is an Android 10 firmware for United States (VZW). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build A015VVRS1ATE1: bootloader binary raised from 1 to 2, so after installing it there is no way back to older builds. A newer build for SM-A015V is available: A015VVRSACXA2.

Download firmware
8.7/10 (456)4,448 times
Android 10
OS Version
2020-07-08
Build Date
n/a
Security patch
1
Countries
1
CSC codes
2
Bootloader binary

Bootloader binary 2. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy A01 use bootloader binary A (10) (latest: A015VVRSACXA2). If your device already runs binary A (10), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: A015VVRU2ATG3
    ModelRegionCSC VersionSizeFile nameDownload
    SM-A015V
    VZW United States
    		A015V2ATG3 — —

    No matching downloads

    How to flash A015VVRU2ATG3

    • A015VVRU2ATG3 has bootloader binary 2. Your device must run binary 2 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Display diagonal14.5 cm (5.7")
    • Display resolution720 x 1520 pixels
    • Display typePLS
    • RAM2 GB
    • Rear camera resolution13 MP
    • Rear camera typeDual camera
    • Battery capacity3000 mAh
    • Weight149 g

    Specifications of SM-A015F, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    A015VVRU2ATG3 is Android 10 firmware for Samsung Galaxy A01, released for United States (VZW). Samsung built it on 2020-07-08.

    No. A newer build for SM-A015V is available: A015VVRSACXA2. Install it instead of A015VVRU2ATG3 unless you need this exact version. The previous build was A015VVRS1ATE1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy A01 must be on bootloader binary 2 or lower.

    This build uses bootloader binary 2. It can be flashed on a Samsung Galaxy A01 running binary 2 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". No other build of this model uses binary 2.

    Other builds and changelog for Samsung Galaxy A01

    No changelog details available.
    Model firmware by region