Samsung Galaxy Core Prime G360HDDU0AOK2
SM-G360H 6 countries Android 4.4.4 (KitKat)

Samsung Galaxy Core Prime G360HDDU0AOK2 Firmware

Samsung Galaxy Core Prime G360HDDU0AOK2 is an Android 4.4.4 (KitKat) firmware for 6 countries, 6 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G360HXXU0AOK1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-G360H is available: G360HDDU0AQG3.

Download firmware
8.8/10 (462)26,152 times
Android 4.4.4 (KitKat)
OS Version
2015-11-06
Build Date
6
Countries
6
CSC codes
0
Bootloader binary

Bootloader binary 0. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: G360HDDU0AOK2
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-G360H
    INS India
    NPL Nepal
    SLK Sri Lanka
    		G360HODD0AOK2 2015-12-01 485.094 MiB
    SM-G360H_1_20170307182926_uuqfd3nmqi_fac.zip
    		Download
    SM-G360H
    THL Thailand
    		G360HOLB0AOK1 — — — Download
    SM-G360H
    XME Malaysia
    		G360HOLB0AOK1 — — — Download
    SM-G360H
    XXV Vietnam
    		G360HOLB0AOK1 — — — Download

    No matching downloads

    How to flash G360HDDU0AOK2

    • G360HDDU0AOK2 has bootloader binary 0. Your device must run binary 0 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of G360HDDU0AOK2 by region

    Samsung released this build in all regions (3) on the same day, December 1, 2015.

    Device specifications

    • Display diagonal11.4 cm (4.5")
    • Display resolution480 x 800 pixels
    • Display typeTFT
    • Processor frequency1.2 GHz
    • RAM1 GB
    • Rear camera resolution5 MP
    • Rear camera typeSingle camera
    • Battery capacity2000 mAh
    • Weight130 g

    Frequently Asked Questions

    G360HDDU0AOK2 is Android 4.4.4 (KitKat) firmware for Samsung Galaxy Core Prime, released for 6 countries, 6 CSC codes. Samsung built it on 2015-11-06.

    No. A newer build for SM-G360H is available: G360HDDU0AQG3. Install it instead of G360HDDU0AOK2 unless you need this exact version. The previous build was G360HXXU0AOK1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 485.094 MiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Core Prime must be on bootloader binary 0 or lower.

    This build uses bootloader binary 0. It can be flashed on a Samsung Galaxy Core Prime running binary 0 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 39 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Core Prime

    No changelog details available.
    Model firmware by region