Samsung Galaxy Core Prime G360MUBS1BQB1
SM-G360M 1 country Android 5.0.2 (Lollipop)

Samsung Galaxy Core Prime G360MUBS1BQB1 Firmware

Samsung Galaxy Core Prime G360MUBS1BQB1 is an Android 5.0.2 (Lollipop) firmware for Costa Rica (CRM). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G360MVJS1BQB1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-G360M is available: G360MVJS1BSA2.

Download firmware
9.4/10 (477)4,436 times
Android 5.0.2 (Lollipop)
OS Version
2017-02-10
Build Date
1
Countries
1
CSC codes
1
Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: G360MUBU1BQB1
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-G360M
    CRM Costa Rica
    		G360MTFG1BPE4 2017-03-09 814.719 MiB
    SM-G360M_1_20181228085953_a025sewp8a_fac.zip
    		Download

    No matching downloads

    How to flash G360MUBS1BQB1

    • G360MUBS1BQB1 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Display diagonal11.4 cm (4.5")
    • Display resolution480 x 800 pixels
    • Display typeTFT
    • RAM2 GB
    • Rear camera resolution5 MP
    • Rear camera typeSingle camera
    • Battery capacity2000 mAh
    • Weight130 g

    Specifications of SM-G360F, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    G360MUBS1BQB1 is Android 5.0.2 (Lollipop) firmware for Samsung Galaxy Core Prime, released for Costa Rica (CRM). Samsung built it on 2017-02-10.

    No. A newer build for SM-G360M is available: G360MVJS1BSA2. Install it instead of G360MUBS1BQB1 unless you need this exact version. The previous build was G360MVJS1BQB1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 814.719 MiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Core Prime must be on bootloader binary 1 or lower.

    This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy Core Prime running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 56 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Core Prime

    No changelog details available.
    Model firmware by region