Samsung Galaxy Xcover3 G389FXXS1APL2
SM-G389F 1 country Android 6.0.1 (Marshmallow)

Samsung Galaxy Xcover3 G389FXXS1APL2 Firmware

Samsung Galaxy Xcover3 G389FXXS1APL2 is an Android 6.0.1 (Marshmallow) firmware for Belgium (PRO). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G389FXXS1APL1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-G389F is available: G389FXXU1AVGL.

Download firmware
9.1/10 (463)4,304 times
Android 6.0.1 (Marshmallow)
OS Version
2016-12-14
Build Date
1
Countries
1
CSC codes
1
Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: G389FXXS1APL2
    ModelRegionCSC VersionSizeFile nameDownload
    SM-G389F
    PRO Belgium
    		G389FVFG1APG2 — — Download

    No matching downloads

    How to flash G389FXXS1APL2

    • G389FXXS1APL2 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Display diagonal11.4 cm (4.5")
    • Display resolution480 x 800 pixels
    • Display typeTFT
    • Processor frequency1.3 GHz
    • RAM1.5 GB
    • Rear camera resolution5 MP
    • Rear camera typeSingle camera
    • SIM cardsSingle SIM
    • Battery capacity2200 mAh
    • Weight154 g

    Frequently Asked Questions

    G389FXXS1APL2 is Android 6.0.1 (Marshmallow) firmware for Samsung Galaxy Xcover3, released for Belgium (PRO). Samsung built it on 2016-12-14.

    No. A newer build for SM-G389F is available: G389FXXU1AVGL. Install it instead of G389FXXS1APL2 unless you need this exact version. The previous build was G389FXXS1APL1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Xcover3 must be on bootloader binary 1 or lower.

    This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy Xcover3 running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 45 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Xcover3

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    No changelog details available.

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    No changelog details available.
    Model firmware by region