SM-G610F 3 countries Android 6.0.1 (Oreo)

Samsung Galaxy J7 Prime G610FDDU1APHA Firmware

Name: Samsung Galaxy J7 Prime (SM-G610F)
Brand: Samsung
Availability: InStock

Samsung Galaxy J7 Prime G610FDDU1APHA is an Android 6.0.1 (Oreo) firmware for Bangladesh (BNG), Nepal (NPL), Sri Lanka (SLK). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. A newer build for SM-G610F is available: G610FDDU1CTG2 https://samfirm.shop/build/G610FDDU1CTG2.

Download firmware 9.4/10 (459)13,027 times

Android 6.0.1 (Oreo)

OS Version

2016-08-16

Build Date

Countries

CSC codes

Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

Not sure which one to download?

Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.

MODEM/CP Version: G610FDDU1APHA

Model	Region	CSC Version	Size	File name	Download
SM-G610F	BNG Bangladesh	G610FODD1APHB	—	—	Download
SM-G610F	NPL Nepal	G610FODD1API2	—	—	Download
SM-G610F	SLK Sri Lanka	G610FODD1API2	—	—	Download

How to flash G610FDDU1APHA

G610FDDU1APHA has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Device specifications

Display diagonal14 cm (5.5")
Display resolution1920 x 1080 pixels
Display typeTFT
Processor frequency1.6 GHz
RAM3 GB
Rear camera resolution13 MP
Rear camera typeSingle camera
SIM cardsDual SIM
Battery capacity3300 mAh
Weight167 g

Frequently Asked Questions

G610FDDU1APHA is Android 6.0.1 (Oreo) firmware for Samsung Galaxy J7 Prime, released for Bangladesh (BNG), Nepal (NPL), Sri Lanka (SLK). Samsung built it on 2016-08-16.

No. A newer build for SM-G610F is available: G610FDDU1CTG2. Install it instead of G610FDDU1APHA unless you need this exact version.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy J7 Prime must be on bootloader binary 1 or lower.

This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy J7 Prime running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 116 other builds of this model use the same binary, so you can switch between them in both directions.