Samsung Galaxy J7 Prime G610MUBU3BRK1
SM-G610M 3 countries Android 7.0 (Nougat)

Samsung Galaxy J7 Prime G610MUBU3BRK1 Firmware

Samsung Galaxy J7 Prime G610MUBU3BRK1 is an Android 7.0 (Nougat) firmware for Argentina (UFN), Dominican Republic (DOR), Panama (PBS, PCW). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G610MUBU2BRH6: bootloader binary raised from 2 to 3, so after installing it there is no way back to older builds. A newer build for SM-G610M is available: G610MUBS8CTH4.

9.3/10 (470)17,211 times
Android 7.0 (Nougat)
OS Version
2018-11-05
First release
other regions until 2018-12-06
n/a
Security patch
3
Countries
4
CSC codes
3
Bootloader binary

Bootloader binary 3. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy J7 Prime use bootloader binary 8 (latest: G610MUBS8CTH4). If your device already runs binary 8, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: G610MUBU3BRK1
    ModelRegionCSC VersionBuild DateRelease dateSizeFile nameDownload
    SM-G610M
    DOR Dominican Republic
    		G610MUWE3BRK1 2018-11-05 2019-02-01 2.202 GiB
    SM-G610M_1_20200901235003_pwx0i756q1_fac.zip
    SM-G610M
    PBS Panama
    		G610MUWT3BRK2 2018-11-05 2019-02-18 2.507 GiB
    SM-G610M_1_20200901234804_137r3b9ttp_fac.zip
    SM-G610M
    PCW Panama
    		G610MUUB3BRK1 2018-12-06 2018-12-28 2.304 GiB
    SM-G610M_1_20200829002034_gys5xp53m7_fac.zip
    SM-G610M
    UFN Argentina
    		G610MUWT3BRK1 2018-11-05 2019-01-04 2.464 GiB
    SM-G610M_1_20190413055027_2loogj6jgs_fac.zip

    No matching downloads

    Device specifications

    • Display diagonal14 cm (5.5")
    • Display resolution1920 x 1080 pixels
    • Display typeTFT
    • RAM3 GB
    • Rear camera resolution13 MP
    • Rear camera typeSingle camera
    • Battery capacity3300 mAh
    • Weight167 g

    Specifications of SM-G610, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    How to flash G610MUBU3BRK1

    • G610MUBU3BRK1 has bootloader binary 3. Your device must run binary 3 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Frequently Asked Questions

    G610MUBU3BRK1 is Android 7.0 (Nougat) firmware for Samsung Galaxy J7 Prime, released for Argentina (UFN), Dominican Republic (DOR), Panama (PBS, PCW). Samsung built it on 2018-11-05.

    No. A newer build for SM-G610M is available: G610MUBS8CTH4. Install it instead of G610MUBU3BRK1 unless you need this exact version. The previous build was G610MUBU2BRH6.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy J7 Prime must be on bootloader binary 3 or lower.

    This build uses bootloader binary 3. It can be flashed on a Samsung Galaxy J7 Prime running binary 3 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 4 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy J7 Prime

    No changelog details available.
    No changelog details available.
    No changelog details available.

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    No changelog details available.
    Show 15 older builds
    No changelog details available.
    No changelog details available.
    No changelog details available.
    No changelog details available.

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    No changelog details available.
    No changelog details available.
    No changelog details available.

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    · Security patch update
    No changelog details available.

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    Model firmware by region