Samsung Galaxy XCover Pro G715AUCS9DWB2
SM-G715A 1 country Android 13

Samsung Galaxy XCover Pro G715AUCS9DWB2 Firmware

Samsung Galaxy XCover Pro G715AUCS9DWB2 is an Android 13 firmware for United States (ATT). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G715AUCU9DWA2, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-G715A is available: G715AUCSEEXB1.

OS updates guaranteed until: Android 13Security updates until: Jan 28, 2024
Download firmware
9.4/10 (35)148 times
Android 13
OS Version
2023-02-20
Build Date
1
Countries
1
CSC codes
9
Bootloader binary

Bootloader binary 9. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy XCover Pro use bootloader binary E (14) (latest: G715AUCSEEXB1). If your device already runs binary E (14), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: G715AUCS9DWB2
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-G715A
    ATT United States
    		G715AATT9DWB2 2023-02-23 4.192 GiB
    SM-G715A_4_20230220155511_hr6fk3ubov_fac.zip

    No matching downloads

    How to flash G715AUCS9DWB2

    • G715AUCS9DWB2 has bootloader binary 9. Your device must run binary 9 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid 10.0
    • Display diagonal16 cm (6.3")
    • Display resolution2340 x 1080 pixels
    • Display typeTFT
    • RAM4 GB
    • Rear camera resolution25 MP
    • Rear camera typeDual camera
    • Battery capacity4050 mAh
    • Weight220 g

    Specifications of SM-G715, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    G715AUCS9DWB2 is Android 13 firmware for Samsung Galaxy XCover Pro, released for United States (ATT). Samsung built it on 2023-02-20.

    No. A newer build for SM-G715A is available: G715AUCSEEXB1. Install it instead of G715AUCS9DWB2 unless you need this exact version. The previous build was G715AUCU9DWA2.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 4.192 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy XCover Pro must be on bootloader binary 9 or lower.

    This build uses bootloader binary 9. It can be flashed on a Samsung Galaxy XCover Pro running binary 9 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 2 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy XCover Pro

    No changelog details available.
    Model firmware by region