Samsung Galaxy XCover Pro G715AUCSBEWE4
SM-G715A 1 country Android 13

Samsung Galaxy XCover Pro G715AUCSBEWE4 Firmware

Samsung Galaxy XCover Pro G715AUCSBEWE4 is an Android 13 firmware for United States (ATT). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G715AUCUAEWD1: bootloader binary raised from A (10) to B (11), so after installing it there is no way back to older builds. A newer build for SM-G715A is available: G715AUCSEEXB1.

OS updates guaranteed until: Android 13Security updates until: Jan 1, 2024
Download firmware
8.9/10 (32)344 times
Android 13
OS Version
2023-05-30
Build Date
1
Countries
1
CSC codes
B (11)
Bootloader binary

Bootloader binary B (11). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy XCover Pro use bootloader binary E (14) (latest: G715AUCSEEXB1). If your device already runs binary E (14), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: G715AUCSBEWE4
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-G715A
    ATT United States
    		G715AATTBEWE4 2023-06-07 4.282 GiB
    SM-G715A_4_20230530133410_y31jw6u1vg_fac.zip
    		Download

    No matching downloads

    How to flash G715AUCSBEWE4

    • G715AUCSBEWE4 has bootloader binary B (11). Your device must run binary B (11) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid 10.0
    • Display diagonal16 cm (6.3")
    • Display resolution2340 x 1080 pixels
    • Display typeTFT
    • RAM4 GB
    • Rear camera resolution25 MP
    • Rear camera typeDual camera
    • Battery capacity4050 mAh
    • Weight220 g

    Specifications of SM-G715, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    G715AUCSBEWE4 is Android 13 firmware for Samsung Galaxy XCover Pro, released for United States (ATT). Samsung built it on 2023-05-30.

    No. A newer build for SM-G715A is available: G715AUCSEEXB1. Install it instead of G715AUCSBEWE4 unless you need this exact version. The previous build was G715AUCUAEWD1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 4.282 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy XCover Pro must be on bootloader binary B (11) or lower.

    This build uses bootloader binary B (11). It can be flashed on a Samsung Galaxy XCover Pro running binary B (11) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". No other build of this model uses binary B (11).

    Other builds and changelog for Samsung Galaxy XCover Pro

    No changelog details available.
    Model firmware by region