Samsung Galaxy S5 G900FDXU1ANI3
SM-G900F 1 country Android 4.4.2 (KitKat)

Samsung Galaxy S5 G900FDXU1ANI3 Firmware

Samsung Galaxy S5 G900FDXU1ANI3 is an Android 4.4.2 (KitKat) firmware for Singapore (MM1, STH, XSP). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G900FXXU1ANI3, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-G900F is available: G900FXXS1PPCG.

Download firmware
8.9/10 (474)13,253 times
Android 4.4.2 (KitKat)
OS Version
2014-09-30
Build Date
1
Countries
3
CSC codes
1
Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: G900FDXU1ANE2
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-G900F
    MM1, STH, XSP Singapore
    		G900FOLC1ANI1 2014-10-20 1.925 GiB
    SM-G900F_1_20160901165327_hzf63kv9uy_fac.zip

    No matching downloads

    How to flash G900FDXU1ANI3

    • G900FDXU1ANI3 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of G900FDXU1ANI3 by region

    First release
    October 20, 2014
    Last region
    October 23, 2014
    Duration
    4 days
    Regions
    3
    1. Day 1 · · 1 region
      SingaporeXSP
    2. Day 4 · · 2 regions
      SingaporeMM1STH

    Device specifications

    • Display diagonal12.9 cm (5.1")
    • Display resolution1920 x 1080 pixels
    • Display typeSAMOLED
    • Processor frequency2.5 GHz
    • RAM2 GB
    • Rear camera resolution16 MP
    • Rear camera typeSingle camera
    • SIM cardsSingle SIM
    • Battery capacity2800 mAh
    • Weight145 g

    Frequently Asked Questions

    G900FDXU1ANI3 is Android 4.4.2 (KitKat) firmware for Samsung Galaxy S5, released for Singapore (MM1, STH, XSP). Samsung built it on 2014-09-30.

    No. A newer build for SM-G900F is available: G900FXXS1PPCG. Install it instead of G900FDXU1ANI3 unless you need this exact version. The previous build was G900FXXU1ANI3.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 1.925 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy S5 must be on bootloader binary 1 or lower.

    This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy S5 running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 289 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy S5

    No changelog details available.
    Model firmware by region