Samsung Galaxy S6 Edge+ G928GUBS5CTK5
SM-G928G 2 countries Android 7.0 (Nougat)

Samsung Galaxy S6 Edge+ G928GUBS5CTK5 Firmware

Samsung Galaxy S6 Edge+ G928GUBS5CTK5 is an Android 7.0 (Nougat) firmware for Guatemala (TGU), Nicaragua (NBS). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G928GUBS5CTK4: security patch 2018-07-01 instead of 2018-06-01. A newer build for SM-G928G is available: G928GUBU5CVGH.

Download firmware
9.1/10 (495)8,788 times
Android 7.0 (Nougat)
OS Version
2020-12-18
Build Date
2018-07-01
Security patch
2
Countries
2
CSC codes
5
Bootloader binary

Bootloader binary 5. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: G928GUBS5CTK5
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-G928G
    NBS Nicaragua
    TGU Guatemala
    		G928GTFG5CTK2 2020-12-18 2.239 GiB
    SM-G928G_1_20201218083504_cfyxddfq04_fac.zip
    		Download

    No matching downloads

    How to flash G928GUBS5CTK5

    • G928GUBS5CTK5 has bootloader binary 5. Your device must run binary 5 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    What's new in G928GUBS5CTK5

    · Security patch update

    Rollout of G928GUBS5CTK5 by region

    Samsung released this build in all regions (2) on the same day, December 18, 2020.

    Device specifications

    • Launched withAndroid 5.1
    • Display diagonal14.5 cm (5.7")
    • Display resolution2560 x 1440 pixels
    • Display typeSAMOLED
    • RAM4 GB
    • Rear camera resolution16 MP
    • Rear camera typeSingle camera
    • Battery capacity3000 mAh
    • Weight153 g

    Specifications of SM-G928, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    G928GUBS5CTK5 is Android 7.0 (Nougat) firmware for Samsung Galaxy S6 Edge+, released for Guatemala (TGU), Nicaragua (NBS). It includes the 2018-07-01 security patch. Samsung built it on 2020-12-18.

    No. A newer build for SM-G928G is available: G928GUBU5CVGH. Install it instead of G928GUBS5CTK5 unless you need this exact version. The previous build was G928GUBS5CTK4.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 2.239 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy S6 Edge+ must be on bootloader binary 5 or lower.

    This build uses bootloader binary 5. It can be flashed on a Samsung Galaxy S6 Edge+ running binary 5 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 47 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy S6 Edge+

    • GPS
    The stability has been improved.

    · Security patch update
    Model firmware by region