Samsung Galaxy S Ⅱ I9100UHLPJ
GT-I9100 1 country Android 2.3.4 (Gingerbread)

Samsung Galaxy S Ⅱ I9100UHLPJ Firmware

Samsung Galaxy S Ⅱ I9100UHLPJ is an Android 2.3.4 (Gingerbread) firmware for Trinidad & Tobago (EON). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build I9100UHLPI: Android updated from Jelly(Android Bean) to Android 2.3.4 (Gingerbread). A newer build for GT-I9100 is available: I9100ZSMSA.

Download firmware
9.3/10 (480)8,649 times
Android 2.3.4 (Gingerbread)
OS Version
2012-04-05
Build Date
1
Countries
1
CSC codes
U (30)
Bootloader binary

Bootloader binary U (30). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy S Ⅱ use bootloader binary Z (35) (latest: I9100ZSMSA). If your device already runs binary Z (35), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    ModelRegionCSC VersionMODEM/CP VersionBuild DateRelease dateSizeFile nameDownload
    GT-I9100
    EON Trinidad & Tobago
    		I9100UHLPFI9100EONLP2 2012-04-05 — — — Download
    GT-I9100
    EON Trinidad & Tobago
    		I9100EONLP2I9100UHLPF — 2012-09-11 — — Download

    No matching downloads

    How to flash I9100UHLPJ

    • I9100UHLPJ has bootloader binary U (30). Your device must run binary U (30) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid 2.3
    • Display diagonal10.8 cm (4.27")
    • Display resolution480 x 800 pixels
    • Display typeAMOLED
    • Processor frequency1.2 GHz
    • Rear camera resolution8 MP
    • Rear camera typeSingle camera
    • SIM cardsSingle SIM
    • Battery capacity1650 mAh
    • Weight116 g

    Frequently Asked Questions

    I9100UHLPJ is Android 2.3.4 (Gingerbread) firmware for Samsung Galaxy S Ⅱ, released for Trinidad & Tobago (EON). Samsung built it on 2012-04-05.

    No. A newer build for GT-I9100 is available: I9100ZSMSA. Install it instead of I9100UHLPJ unless you need this exact version. The previous build was I9100UHLPI.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy S Ⅱ must be on bootloader binary U (30) or lower.

    This build uses bootloader binary U (30). It can be flashed on a Samsung Galaxy S Ⅱ running binary U (30) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 10 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy S Ⅱ

    No changelog details available.
    Model firmware by region