Samsung Galaxy S Ⅱ I9100UHLPO Firmware
Samsung Galaxy S Ⅱ I9100UHLPO is an Android 4.0.3 (Ice Cream Sandwich) firmware for Chile (CRC), Panama (CPA, PBS, PCW). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build I9100UHLPN https://samfirm.shop/build/I9100UHLPN: Android updated from Ice(Android Cream) to Android 4.0.3 (Ice Cream Sandwich). A newer build for GT-I9100 is available: I9100ZSMSA https://samfirm.shop/build/I9100ZSMSA.
Android 4.0.3 (Ice Cream Sandwich)
OS Version
2012-05-12
First release
other regions until 2012-08-16
2
Countries
4
CSC codes
U (30)
Bootloader binary
Bootloader binary U (30). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.
Newer builds of Samsung Galaxy S Ⅱ use bootloader binary Z (35) (latest: I9100ZSMSA https://samfirm.shop/build/I9100ZSMSA). If your device already runs binary Z (35), this build cannot be flashed.
All regional downloads
Pick your region (CSC) to download the matching firmware package.
Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
No matching downloads
How to flash I9100UHLPO
- I9100UHLPO has bootloader binary U (30). Your device must run binary U (30) or lower: it is the 5th character from the end of your current build number.
- CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
- HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
- The Download Mode key combo depends on the model: see all combos.
Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.
Rollout of I9100UHLPO by region
- First release
- July 27, 2012
- Last region
- August 31, 2012
- Duration
- 36 days
- Regions
- 4
- Day 1 · · 3 regionsPanamaCPAPBSPCW
- Day 36 · · 1 regionChileCRC
Device specifications
- Launched withAndroid 2.3
- Display diagonal10.8 cm (4.27")
- Display resolution480 x 800 pixels
- Display typeAMOLED
- Processor frequency1.2 GHz
- Rear camera resolution8 MP
- Rear camera typeSingle camera
- SIM cardsSingle SIM
- Battery capacity1650 mAh
- Weight116 g
Frequently Asked Questions
I9100UHLPO is Android 4.0.3 (Ice Cream Sandwich) firmware for Samsung Galaxy S Ⅱ, released for Chile (CRC), Panama (CPA, PBS, PCW). Samsung built it on 2012-05-12.
No. A newer build for GT-I9100 is available: I9100ZSMSA. Install it instead of I9100UHLPO unless you need this exact version. The previous build was I9100UHLPN.
Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy S Ⅱ must be on bootloader binary U (30) or lower.
This build uses bootloader binary U (30). It can be flashed on a Samsung Galaxy S Ⅱ running binary U (30) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 10 other builds of this model use the same binary, so you can switch between them in both directions.
Other builds and changelog for Samsung Galaxy S Ⅱ
No changelog details available.
- I9100ZSMSASep 16, 2013
- I9100ZCLSJJul 23, 2013
- I9100ZCLSG
- I9100XXMS7May 22, 2014
- I9100XXMS1May 22, 2014
- I9100XWMS3Dec 23, 2013
- I9100XWMS2Dec 3, 2013
- I9100XWMS1Sep 25, 2013
- I9100XWLSZSep 10, 2013
- I9100XWLSYMay 31, 2013
- I9100XWLSWMay 16, 2013
- I9100XWLSUApr 23, 2013
- I9100XWLSTApr 24, 2013
- I9100XWLSSApr 22, 2013
- I9100XWLSN
- I9100XWLSJ
- I9100XWLSHFeb 26, 2013
- I9100XWLSEFeb 14, 2013
- I9100XWLSDJan 31, 2013
- I9100XWLSB