Samsung Galaxy S 4 Active I9295XXSDPL3 Firmware
Samsung Galaxy S 4 Active I9295XXSDPL3 is an Android 5.0.1 (Jelly) firmware for 15 countries, 16 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build I9295XXSDPL2: Android updated from Android 5.0.1 (Lollipop) to Android 5.0.1 (Jelly). A newer build for GT-I9295 is available: I9295XXUDRB1.
9.1/10 (451)108,797 times
Android 5.0.1 (Jelly)
OS Version
2016-12-27
First release
other regions until 2017-04-27
n/a
Security patch
15
Countries
16
CSC codes
S (28)
Bootloader binary
Bootloader binary S (28). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.
Newer builds of Samsung Galaxy S 4 Active use bootloader binary U (30) (latest: I9295XXUDRB1). If your device already runs binary U (30), this build cannot be flashed.
All regional downloads
Pick your region (CSC) to download the matching firmware package.
Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
20
MODEM/CP Version: I9295XXSDPL3
No matching downloads
Device specifications
- Launched withAndroid 4.2.2
- Display diagonal12.7 cm (5")
- Display resolution1920 x 1080 pixels
- Display typeTFT
- Processor frequency1.9 GHz
- Processor familyQualcomm Snapdragon
- Processor model600
- RAM2 GB
- Rear camera resolution8 MP
- Rear camera typeSingle camera
- SIM cardsSingle SIM
- Battery capacity2600 mAh
- Weight153 g
How to flash I9295XXSDPL3
- Install Samsung USB Drivers:Download Official Drivers
- Download Odin Flash Tool:
- I9295XXSDPL3 has bootloader binary S (28). Your device must run binary S (28) or lower: it is the 5th character from the end of your current build number.
- CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
- HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
- The Download Mode key combo depends on the model: see all combos.
Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.
Frequently Asked Questions
I9295XXSDPL3 is Android 5.0.1 (Jelly) firmware for Samsung Galaxy S 4 Active, released for 15 countries, 16 CSC codes. Samsung built it on 2016-12-27.
No. A newer build for GT-I9295 is available: I9295XXUDRB1. Install it instead of I9295XXSDPL3 unless you need this exact version. The previous build was I9295XXSDPL2.
Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy S 4 Active must be on bootloader binary S (28) or lower.
This build uses bootloader binary S (28). It can be flashed on a Samsung Galaxy S 4 Active running binary S (28) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 11 other builds of this model use the same binary, so you can switch between them in both directions.