Samsung Galaxy J1 Mini Prime J106MUBU0APK1
SM-J106M 2 countries Android 6.0.1 (Marshmallow)

Samsung Galaxy J1 Mini Prime J106MUBU0APK1 Firmware

Samsung Galaxy J1 Mini Prime J106MUBU0APK1 is an Android 6.0.1 (Marshmallow) firmware for Argentina (CTI, PSN, UFN), Ecuador (ALE). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. A newer build for SM-J106M is available: J106MUBU0ARL2.

Download firmware
9.0/10 (461)17,478 times
Android 6.0.1 (Marshmallow)
OS Version
2016-11-03
Build Date
2
Countries
4
CSC codes
0
Bootloader binary

Bootloader binary 0. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: J106MUBU0APK1
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-J106M
    ALE Ecuador
    		J106MUUB0APL2 — — — Download
    SM-J106M
    CTI Argentina
    		J106MUWA0APK1 2017-01-11 1.426 GiB
    SM-J106M_1_20180829215227_pyjtz2tumh_fac.zip
    		Download
    SM-J106M
    PSN Argentina
    		J106M0APK1 — — — Download
    SM-J106M
    UFN Argentina
    		J106MUWT0APK2 2017-01-10 1.316 GiB
    SM-J106M_1_20180829040740_p40khi255p_fac.zip
    		Download

    No matching downloads

    How to flash J106MUBU0APK1

    • J106MUBU0APK1 has bootloader binary 0. Your device must run binary 0 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of J106MUBU0APK1 by region

    First release
    January 10, 2017
    Last region
    January 11, 2017
    Duration
    2 days
    Regions
    2
    1. Day 1 · · 1 region
      ArgentinaUFN
    2. Day 2 · · 1 region
      ArgentinaCTI

    Device specifications

    • Display diagonal10.2 cm (4")
    • Display resolution480 x 800 pixels
    • Display typeTFT
    • RAM1 GB
    • Rear camera resolution5 MP
    • Rear camera typeSingle camera
    • Battery capacity1500 mAh
    • Weight123 g

    Specifications of SM-J106, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    J106MUBU0APK1 is Android 6.0.1 (Marshmallow) firmware for Samsung Galaxy J1 Mini Prime, released for Argentina (CTI, PSN, UFN), Ecuador (ALE). Samsung built it on 2016-11-03.

    No. A newer build for SM-J106M is available: J106MUBU0ARL2. Install it instead of J106MUBU0APK1 unless you need this exact version.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy J1 Mini Prime must be on bootloader binary 0 or lower.

    This build uses bootloader binary 0. It can be flashed on a Samsung Galaxy J1 Mini Prime running binary 0 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 21 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy J1 Mini Prime

    No changelog details available.
    Model firmware by region