Samsung Galaxy J1 Ace J110MUBU0AOGC
SM-J110M 3 countries Android 5.1.1 (Lollipop)

Samsung Galaxy J1 Ace J110MUBU0AOGC Firmware

Samsung Galaxy J1 Ace J110MUBU0AOGC is an Android 5.1.1 (Lollipop) firmware for Panama (TPA), Trinidad & Tobago (TTT), Uruguay (UPO). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. A newer build for SM-J110M is available: J110MUBS0ASA1.

9.1/10 (454)12,740 times
Android 5.1.1 (Lollipop)
OS Version
2015-07-31
First release
other regions until 2015-08-06
n/a
Security patch
3
Countries
3
CSC codes
0
Bootloader binary

Bootloader binary 0. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    ModelRegionCSC VersionMODEM/CP VersionBuild DateRelease dateSizeFile nameDownload
    SM-J110M
    TPA Panama
    		J110MUUB0AOGCJ110MUBU0AOGC 2015-07-31 — — —
    SM-J110M
    TTT Trinidad & Tobago
    		J110MUUB0AOGCJ110MUBU0AOH2 2015-08-06 2015-09-16 767.372 MiB
    SM-J110M_1_20151109092853_jb3h4icqga_fac.zip
    SM-J110M
    UPO Uruguay
    		J110MUUB0AOGCJ110MUBU0AOGC 2015-08-06 — — —

    No matching downloads

    How to flash J110MUBU0AOGC

    • J110MUBU0AOGC has bootloader binary 0. Your device must run binary 0 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of J110MUBU0AOGC by region

    Samsung released this build in all regions (1) on the same day, September 16, 2015.

    Device specifications

    • Display diagonal10.9 cm (4.3")
    • Display resolution480 x 800 pixels
    • Display typeSAMOLED
    • RAM0.75 GB
    • Rear camera resolution5 MP
    • Rear camera typeSingle camera
    • Battery capacity1900 mAh
    • Weight131 g

    Specifications of SM-J110, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    J110MUBU0AOGC is Android 5.1.1 (Lollipop) firmware for Samsung Galaxy J1 Ace, released for Panama (TPA), Trinidad & Tobago (TTT), Uruguay (UPO). Samsung built it on 2015-07-31.

    No. A newer build for SM-J110M is available: J110MUBS0ASA1. Install it instead of J110MUBU0AOGC unless you need this exact version.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 767.372 MiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy J1 Ace must be on bootloader binary 0 or lower.

    This build uses bootloader binary 0. It can be flashed on a Samsung Galaxy J1 Ace running binary 0 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 20 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy J1 Ace

    No changelog details available.
    Model firmware by region