Samsung Galaxy J1 Ace J110MUBU0APK1
SM-J110M 11 countries Android 5.1.1 (Lollipop)

Samsung Galaxy J1 Ace J110MUBU0APK1 Firmware

Samsung Galaxy J1 Ace J110MUBU0APK1 is an Android 5.1.1 (Lollipop) firmware for 11 countries, 11 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J110MUBU0APD1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-J110M is available: J110MUBS0ASA1.

Download firmware
8.9/10 (460)52,344 times
Android 5.1.1 (Lollipop)
OS Version
2016-11-21
Build Date
11
Countries
11
CSC codes
0
Bootloader binary

Bootloader binary 0. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    12
    MODEM/CP Version: J110MUBU0APK1
    ModelRegionCSC VersionBuild DateRelease dateSizeFile nameDownload
    SM-J110M
    CHX Chile
    		J110MCHX0APL1 — — — — Download
    SM-J110M
    COB Colombia
    		J110MTFG0APL1 — — — — Download
    SM-J110M
    CRM Costa Rica
    		J110MTFG0APL1 — — — — Download
    SM-J110M
    CUE Cuba
    		J110M0APL1 2016-11-21 — — — Download
    SM-J110M
    CUE Cuba
    		J110MCUE0APL1 2016-11-21 2017-01-10 — — Download
    SM-J110M
    EBE Ecuador
    		J110MTFG0APL1 — — — — Download
    SM-J110M
    NBS Nicaragua
    		J110MTFG0APL1 — — — — Download
    SM-J110M
    PBS Panama
    		J110MTFG0APL1 — — — — Download
    SM-J110M
    TGU Guatemala
    		J110MTFG0APL1 — — — — Download
    SM-J110M
    TMM Mexico
    		J110MTFG0APL1 — — — — Download
    SM-J110M
    UFN Argentina
    		J110MTFG0APL1 — — — — Download
    SM-J110M
    UFU Uruguay
    		J110MTFG0APL1 — — — — Download

    No matching downloads

    How to flash J110MUBU0APK1

    • J110MUBU0APK1 has bootloader binary 0. Your device must run binary 0 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of J110MUBU0APK1 by region

    Samsung released this build in all regions (1) on the same day, January 10, 2017.

    Device specifications

    • Display diagonal10.9 cm (4.3")
    • Display resolution480 x 800 pixels
    • Display typeSAMOLED
    • RAM0.75 GB
    • Rear camera resolution5 MP
    • Rear camera typeSingle camera
    • Battery capacity1900 mAh
    • Weight131 g

    Specifications of SM-J110, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    J110MUBU0APK1 is Android 5.1.1 (Lollipop) firmware for Samsung Galaxy J1 Ace, released for 11 countries, 11 CSC codes. Samsung built it on 2016-11-21.

    No. A newer build for SM-J110M is available: J110MUBS0ASA1. Install it instead of J110MUBU0APK1 unless you need this exact version. The previous build was J110MUBU0APD1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy J1 Ace must be on bootloader binary 0 or lower.

    This build uses bootloader binary 0. It can be flashed on a Samsung Galaxy J1 Ace running binary 0 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 20 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy J1 Ace

    No changelog details available.
    Model firmware by region