Samsung Galaxy J2 J200MUBU2AQB2
SM-J200M 1 country Android 5.1.1 (Lollipop)

Samsung Galaxy J2 J200MUBU2AQB2 Firmware

Samsung Galaxy J2 J200MUBU2AQB2 is an Android 5.1.1 (Lollipop) firmware for Brazil (ZTM, ZTR). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J200MUBU2AQA2, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-J200M is available: J200MUBS2ARK7.

Download firmware
9.4/10 (40)8,925 times
Android 5.1.1 (Lollipop)
OS Version
2017-02-16
First release
other regions until 2017-05-15
1
Countries
2
CSC codes
2
Bootloader binary

Bootloader binary 2. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: J200MUBU2AQB2
    ModelRegionCSC VersionBuild DateRelease dateSizeFile nameDownload
    SM-J200M
    ZTM Brazil
    		J200MZTM2AQB2 2017-05-15 2017-05-15 1.145 GiB
    SM-J200M_1_20170515092700_r000oc5i4g_fac.zip
    SM-J200M
    ZTM Brazil
    		J200M2AQB2 2017-02-16 — — —
    SM-J200M
    ZTR Brazil
    		J200M2AQB2 2017-02-16 — — —

    No matching downloads

    How to flash J200MUBU2AQB2

    • J200MUBU2AQB2 has bootloader binary 2. Your device must run binary 2 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of J200MUBU2AQB2 by region

    Samsung released this build in all regions (1) on the same day, May 15, 2017.

    Device specifications

    • Display diagonal11.9 cm (4.7")
    • Display resolution540 x 960 pixels
    • Display typeSAMOLED
    • RAM1 GB
    • Rear camera resolution5 MP
    • Rear camera typeSingle camera
    • Battery capacity2000 mAh
    • Weight130 g

    Specifications of SM-J200, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    J200MUBU2AQB2 is Android 5.1.1 (Lollipop) firmware for Samsung Galaxy J2, released for Brazil (ZTM, ZTR). Samsung built it on 2017-02-16.

    No. A newer build for SM-J200M is available: J200MUBS2ARK7. Install it instead of J200MUBU2AQB2 unless you need this exact version. The previous build was J200MUBU2AQA2.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 1.145 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy J2 must be on bootloader binary 2 or lower.

    This build uses bootloader binary 2. It can be flashed on a Samsung Galaxy J2 running binary 2 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 26 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy J2

    No changelog details available.
    Model firmware by region