Samsung Galaxy J2 Core J260MUBU2ARJ4
SM-J260M 1 country Android 8.1.0 (Oreo)

Samsung Galaxy J2 Core J260MUBU2ARJ4 Firmware

Samsung Galaxy J2 Core J260MUBU2ARJ4 is an Android 8.1.0 (Oreo) firmware for Brazil (ZVV). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J260MUBU1ARJ1: bootloader binary raised from 1 to 2, so after installing it there is no way back to older builds. A newer build for SM-J260M is available: J260MUBSDAUJ4.

Download firmware
9.0/10 (457)4,437 times
Android 8.1.0 (Oreo)
OS Version
1
Countries
1
CSC codes
2
Bootloader binary

Bootloader binary 2. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy J2 Core use bootloader binary D (13) (latest: J260MUBSDAUJ4). If your device already runs binary D (13), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: J260MUBU2ARJ1
    ModelRegionCSC VersionSizeFile nameDownload
    SM-J260M
    ZVV Brazil
    		J260MZVV2ARJ1 — — Download

    No matching downloads

    How to flash J260MUBU2ARJ4

    • J260MUBU2ARJ4 has bootloader binary 2. Your device must run binary 2 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Display diagonal12.7 cm (5")
    • Display resolution540 x 960 pixels
    • Display typePLS
    • Processor frequency1.4 GHz
    • Processor familySamsung Exynos
    • Processor model7570
    • RAM1 GB
    • Rear camera resolution8 MP
    • Rear camera typeSingle camera
    • SIM cardsDual SIM
    • Battery capacity2600 mAh
    • Weight154 g

    Frequently Asked Questions

    J260MUBU2ARJ4 is Android 8.1.0 (Oreo) firmware for Samsung Galaxy J2 Core, released for Brazil (ZVV).

    No. A newer build for SM-J260M is available: J260MUBSDAUJ4. Install it instead of J260MUBU2ARJ4 unless you need this exact version. The previous build was J260MUBU1ARJ1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy J2 Core must be on bootloader binary 2 or lower.

    This build uses bootloader binary 2. It can be flashed on a Samsung Galaxy J2 Core running binary 2 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 16 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy J2 Core

    • The security of your device has been improved.

    • Overall stability of your device has been improved.

    · The security of your device has been improved.

    • LGPD (General Personal Data Protection Law) has been applied.
    • The security of your device has been improved.

    • The security of your device has been improved.

    Model firmware by region