Samsung Galaxy J3(2017) J330FNXXS3BRI2
SM-J330FN 1 country Android 8.0.0 (Pie)

Samsung Galaxy J3(2017) J330FNXXS3BRI2 Firmware

Samsung Galaxy J3(2017) J330FNXXS3BRI2 is an Android 8.0.0 (Pie) firmware for Italy (ITV). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J330FNXXU3BRI1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-J330FN is available: J330FNXXU4CZC1.

Download firmware
9.0/10 (460)4,374 times
Android 8.0.0 (Pie)
OS Version
2018-09-05
Build Date
1
Countries
1
CSC codes
3
Bootloader binary

Bootloader binary 3. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy J3(2017) use bootloader binary 4 (latest: J330FNXXU4CZC1). If your device already runs binary 4, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: J330FNXXS3BRI2
    ModelRegionCSC VersionSizeFile nameDownload
    SM-J330FN
    ITV Italy
    		J330FNOXA3BRG2 — — Download

    No matching downloads

    How to flash J330FNXXS3BRI2

    • J330FNXXS3BRI2 has bootloader binary 3. Your device must run binary 3 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Display diagonal12.7 cm (5")
    • Display resolution1280 x 720 pixels
    • Display typeSAMOLED
    • Processor frequency1.4 GHz
    • RAM2 GB
    • Rear camera resolution13 MP
    • Rear camera typeSingle camera
    • SIM cardsDual SIM
    • Battery capacity2400 mAh
    • Weight142 g

    Frequently Asked Questions

    J330FNXXS3BRI2 is Android 8.0.0 (Pie) firmware for Samsung Galaxy J3(2017), released for Italy (ITV). Samsung built it on 2018-09-05.

    No. A newer build for SM-J330FN is available: J330FNXXU4CZC1. Install it instead of J330FNXXS3BRI2 unless you need this exact version. The previous build was J330FNXXU3BRI1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy J3(2017) must be on bootloader binary 3 or lower.

    This build uses bootloader binary 3. It can be flashed on a Samsung Galaxy J3(2017) running binary 3 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 33 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy J3(2017)

    No changelog details available.

    · The security of your device has been improved.

    No changelog details available.

    · The security of your device has been improved.

    Model firmware by region