Samsung Galaxy J3(2017) J330FXWS3BSF3 Firmware
Samsung Galaxy J3(2017) J330FXWS3BSF3 is an Android 8.0.0 (Oreo) firmware for TKD, United Arab Emirates (XSG). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J330FXXS3BSF3: Android updated from Android 8.0.0 (Nougat) to Android 8.0.0 (Oreo). A newer build for SM-J330F is available: J330FXXU4CZC2.
9.4/10 (38)8,701 times
Android 8.0.0 (Oreo)
OS Version
2019-06-11
First release
other regions until 2019-06-17
2019-06-01
Security patch
2
Countries
2
CSC codes
3
Bootloader binary
Bootloader binary 3. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.
Newer builds of Samsung Galaxy J3(2017) use bootloader binary 4 (latest: J330FXXU4CZC2). If your device already runs binary 4, this build cannot be flashed.
All regional downloads
Pick your region (CSC) to download the matching firmware package.
Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
No matching downloads
Device specifications
- Display diagonal12.7 cm (5")
- Display resolution1280 x 720 pixels
- Display typeTFT
- Processor frequency1.4 GHz
- RAM2 GB
- Rear camera resolution13 MP
- Rear camera typeSingle camera
- SIM cardsDual SIM
- Battery capacity2400 mAh
- Weight142 g
What's new in J330FXWS3BSF3
· The security of your device has been improved.
How to flash J330FXWS3BSF3
- Install Samsung USB Drivers:Download Official Drivers
- Download Odin Flash Tool:
- J330FXWS3BSF3 has bootloader binary 3. Your device must run binary 3 or lower: it is the 5th character from the end of your current build number.
- CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
- HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
- The Download Mode key combo depends on the model: see all combos.
Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.
Frequently Asked Questions
J330FXWS3BSF3 is Android 8.0.0 (Oreo) firmware for Samsung Galaxy J3(2017), released for TKD, United Arab Emirates (XSG). It includes the 2019-06-01 security patch. Samsung built it on 2019-06-11.
No. A newer build for SM-J330F is available: J330FXXU4CZC2. Install it instead of J330FXWS3BSF3 unless you need this exact version. The previous build was J330FXXS3BSF3.
Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 2.057 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy J3(2017) must be on bootloader binary 3 or lower.
This build uses bootloader binary 3. It can be flashed on a Samsung Galaxy J3(2017) running binary 3 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 45 other builds of this model use the same binary, so you can switch between them in both directions.