Samsung Galaxy J7 J700MUBU2BRB2
SM-J700M 1 country Android 5.1.1 (Lollipop)

Samsung Galaxy J7 J700MUBU2BRB2 Firmware

Samsung Galaxy J7 J700MUBU2BRB2 is an Android 5.1.1 (Lollipop) firmware for Chile (CHE). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J700MUBU2BRA1: Android updated from Android 6.0.1 (Marshmallow) to Android 5.1.1 (Lollipop). A newer build for SM-J700M is available: J700MUBU2BSH1.

Download firmware
9.2/10 (459)4,288 times
Android 5.1.1 (Lollipop)
OS Version
1
Countries
1
CSC codes
2
Bootloader binary

Bootloader binary 2. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: J700MUBU2BQK1
    ModelRegionCSC VersionSizeFile nameDownload
    SM-J700M
    CHE Chile
    		J700MCHE2BRB1 — — Download

    No matching downloads

    How to flash J700MUBU2BRB2

    • J700MUBU2BRB2 has bootloader binary 2. Your device must run binary 2 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Frequently Asked Questions

    J700MUBU2BRB2 is Android 5.1.1 (Lollipop) firmware for Samsung Galaxy J7, released for Chile (CHE).

    No. A newer build for SM-J700M is available: J700MUBU2BSH1. Install it instead of J700MUBU2BRB2 unless you need this exact version. The previous build was J700MUBU2BRA1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy J7 must be on bootloader binary 2 or lower.

    This build uses bootloader binary 2. It can be flashed on a Samsung Galaxy J7 running binary 2 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 67 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy J7

    No changelog details available.

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    No changelog details available.

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    No changelog details available.
    Show 6 older builds

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    No changelog details available.
    Model firmware by region