Samsung Galaxy J7 Neo J701FXXSACUD3
SM-J701F 2 countries Android 9 (Pie)

Samsung Galaxy J7 Neo J701FXXSACUD3 Firmware

Samsung Galaxy J7 Neo J701FXXSACUD3 is an Android 9 (Pie) firmware for Israel (ILO), Turkey (TUR). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J701FXVSACUD2, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-J701F is available: J701FXXUACUH1.

Download firmware
8.9/10 (490)8,802 times
Android 9 (Pie)
OS Version
2021-05-11
First release
other regions until 2021-05-18
2
Countries
2
CSC codes
A (10)
Bootloader binary

Bootloader binary A (10). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: J701FXXSACUC3
    ModelRegionCSC VersionBuild DateRelease dateSizeFile nameDownload
    SM-J701F
    ILO Israel
    		J701FOJKACUC3 2021-05-18 2021-05-18 2.261 GiB
    SM-J701F_1_20210427195737_xr7i0s07r3_fac.zip
    		Download
    SM-J701F
    TUR Turkey
    		J701FOJVACUC3 2021-05-11 2021-05-11 2.341 GiB
    SM-J701F_1_20210427195017_v6rpg7qp6h_fac.zip
    		Download

    No matching downloads

    How to flash J701FXXSACUD3

    • J701FXXSACUD3 has bootloader binary A (10). Your device must run binary A (10) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of J701FXXSACUD3 by region

    First release
    May 11, 2021
    Last region
    May 18, 2021
    Duration
    8 days
    Regions
    2
    1. Day 1 · · 1 region
      TurkeyTUR
    2. Day 8 · · 1 region
      IsraelILO

    Device specifications

    • Display diagonal14 cm (5.5")
    • Display resolution1280 x 720 pixels
    • Display typeSAMOLED
    • Processor frequency1.6 GHz
    • RAM2 GB
    • Rear camera resolution13 MP
    • Rear camera typeSingle camera
    • Battery capacity3500 mAh
    • Weight170 g

    Frequently Asked Questions

    J701FXXSACUD3 is Android 9 (Pie) firmware for Samsung Galaxy J7 Neo, released for Israel (ILO), Turkey (TUR). Samsung built it on 2021-05-11.

    No. A newer build for SM-J701F is available: J701FXXUACUH1. Install it instead of J701FXXSACUD3 unless you need this exact version. The previous build was J701FXVSACUD2.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy J7 Neo must be on bootloader binary A (10) or lower.

    This build uses bootloader binary A (10). It can be flashed on a Samsung Galaxy J7 Neo running binary A (10) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 16 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy J7 Neo

    No changelog details available.
    Model firmware by region