Samsung Galaxy J7(2016) J7108ZMU1BQL1
SM-J7108 1 country Android 6.0.1 (Marshmallow)

Samsung Galaxy J7(2016) J7108ZMU1BQL1 Firmware

Samsung Galaxy J7(2016) J7108ZMU1BQL1 is an Android 6.0.1 (Marshmallow) firmware for China (CHM). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J7108ZHS1BQI1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-J7108 is available: J7108ZHS2BRC1.

Download firmware
9.4/10 (461)8,619 times
Android 6.0.1 (Marshmallow)
OS Version
2017-12-21
Build Date
1
Countries
1
CSC codes
1
Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy J7(2016) use bootloader binary 2 (latest: J7108ZHS2BRC1). If your device already runs binary 2, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: J7108ZMU1BQL1
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-J7108
    CHM China
    		J71081BQL1 2018-01-19 — — Download
    SM-J7108
    CHM China
    		J7108CHM1BQL1 2018-01-12 1.46 GiB
    SM-J7108_1_20180404083527_9cl3gbs2l0_fac.zip
    		Download

    No matching downloads

    How to flash J7108ZMU1BQL1

    • J7108ZMU1BQL1 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    What's new in J7108ZMU1BQL1

    - My Knox service will terminate after 2017/12/19.
      ( Existing installation My Knox  application can be used, you can use this function  untill you uninstall it or make factory reset. )
    - Improved performance
    ㆍBroadcom Wlan firmware security patched.
    - The latest Android security patch has been applied.
    ㆍDevice security has been further enhanced.

    Device specifications

    • Display diagonal14 cm (5.5")
    • Display resolution1280 x 720 pixels
    • Display typeSAMOLED
    • RAM2 GB
    • Rear camera resolution13 MP
    • Rear camera typeSingle camera
    • Battery capacity3300 mAh
    • Weight169 g

    Specifications of SM-J710F, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    J7108ZMU1BQL1 is Android 6.0.1 (Marshmallow) firmware for Samsung Galaxy J7(2016), released for China (CHM). Samsung built it on 2017-12-21.

    No. A newer build for SM-J7108 is available: J7108ZHS2BRC1. Install it instead of J7108ZMU1BQL1 unless you need this exact version. The previous build was J7108ZHS1BQI1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 1.46 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy J7(2016) must be on bootloader binary 1 or lower.

    This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy J7(2016) running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 3 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy J7(2016)

    - The latest Android security patch has been applied.
    ㆍDevice security has been further enhanced.

    - My Knox service will terminate after 2017/12/19.
      ( Existing installation My Knox  application can be used, you can use this function  untill you uninstall it or make factory reset. )
    - Improved performance
    ㆍBroadcom Wlan firmware security patched.
    - The latest Android security patch has been applied.
    ㆍDevice security has been further enhanced.

    - The latest Android security patch has been applied.
    ㆍDevice security has been further enhanced.

    - Other bug fixes
    ㆍFixed the issue that alarm app terminated after back up from PC Smart Switch.
    ㆍBattery capacity display error in Samsung member app has been resolved.
    - The latest Android security patch has been applied.
    ㆍDevice security has been further enhanced.

    ㆍThe latest Android security patch has been applied.
    - Device security has been further enhanced.

    Model firmware by region