Samsung Galaxy J7 Pro J730GDXU3ARB2
SM-J730G 1 country Android 7.0 (Pie)

Samsung Galaxy J7 Pro J730GDXU3ARB2 Firmware

Samsung Galaxy J7 Pro J730GDXU3ARB2 is an Android 7.0 (Pie) firmware for New Zealand (NZC). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J730GDXU3ARB1: Android updated from Android 7.0 (Nougat) to Android 7.0 (Pie). A newer build for SM-J730G is available: J730GUBUDCUG1.

8.8/10 (499)8,622 times
Android 7.0 (Pie)
OS Version
2018-02-27
Build Date
n/a
Security patch
1
Countries
1
CSC codes
3
Bootloader binary

Bootloader binary 3. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy J7 Pro use bootloader binary D (13) (latest: J730GUBUDCUG1). If your device already runs binary D (13), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    ModelRegionCSC VersionMODEM/CP VersionRelease dateSizeFile nameDownload
    SM-J730G
    NZC New Zealand
    		J730G3ARB2J730GDXU3ARB2 — — —
    SM-J730G
    NZC New Zealand
    		J730GNZC3ARB2J730GDXU3ARA2 2018-03-27 1.85 GiB
    SM-J730G_1_20210618155808_3xqwblpn1k_fac.zip

    No matching downloads

    How to flash J730GDXU3ARB2

    • J730GDXU3ARB2 has bootloader binary 3. Your device must run binary 3 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Display diagonal14 cm (5.5")
    • Display resolution1920 x 1080 pixels
    • Display typeSAMOLED
    • Processor frequency1.6 GHz
    • RAM3 GB
    • Rear camera resolution13 MP
    • Rear camera typeSingle camera
    • SIM cardsDual SIM
    • Battery capacity3600 mAh
    • Weight181 g

    Frequently Asked Questions

    J730GDXU3ARB2 is Android 7.0 (Pie) firmware for Samsung Galaxy J7 Pro, released for New Zealand (NZC). Samsung built it on 2018-02-27.

    No. A newer build for SM-J730G is available: J730GUBUDCUG1. Install it instead of J730GDXU3ARB2 unless you need this exact version. The previous build was J730GDXU3ARB1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 1.85 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy J7 Pro must be on bootloader binary 3 or lower.

    This build uses bootloader binary 3. It can be flashed on a Samsung Galaxy J7 Pro running binary 3 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 6 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy J7 Pro

    No changelog details available.
    Model firmware by region