Samsung Galaxy J7 Pro J730GDXU5BRI3
SM-J730G 4 countries Android 8.1.0 (Pie)

Samsung Galaxy J7 Pro J730GDXU5BRI3 Firmware

Samsung Galaxy J7 Pro J730GDXU5BRI3 is an Android 8.1.0 (Pie) firmware for 4 countries, 4 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build J730GUBU5BRI3, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-J730G is available: J730GUBUDCUG1.

8.8/10 (455)17,358 times
Android 8.1.0 (Pie)
OS Version
2018-09-06
Build Date
n/a
Security patch
4
Countries
4
CSC codes
5
Bootloader binary

Bootloader binary 5. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy J7 Pro use bootloader binary D (13) (latest: J730GUBUDCUG1). If your device already runs binary D (13), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: J730GDXU5BRI3
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-J730G
    CAM Cambodia
    SMA Philippines
    XME Malaysia
    XXV Vietnam
    		J730GOLB5BRI3 2018-09-18 1.964 GiB
    SM-J730G_1_20210618154838_y6ib860fqb_fac.zip

    No matching downloads

    How to flash J730GDXU5BRI3

    • J730GDXU5BRI3 has bootloader binary 5. Your device must run binary 5 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of J730GDXU5BRI3 by region

    First release
    September 18, 2018
    Last region
    September 28, 2018
    Duration
    11 days
    Regions
    4
    1. Day 1 · · 3 regions
      CambodiaCAMPhilippinesSMAVietnamXXV
    2. Day 11 · · 1 region
      MalaysiaXME

    Device specifications

    • Display diagonal14 cm (5.5")
    • Display resolution1920 x 1080 pixels
    • Display typeSAMOLED
    • Processor frequency1.6 GHz
    • RAM3 GB
    • Rear camera resolution13 MP
    • Rear camera typeSingle camera
    • SIM cardsDual SIM
    • Battery capacity3600 mAh
    • Weight181 g

    Frequently Asked Questions

    J730GDXU5BRI3 is Android 8.1.0 (Pie) firmware for Samsung Galaxy J7 Pro, released for 4 countries, 4 CSC codes. Samsung built it on 2018-09-06.

    No. A newer build for SM-J730G is available: J730GUBUDCUG1. Install it instead of J730GDXU5BRI3 unless you need this exact version. The previous build was J730GUBU5BRI3.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 1.964 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy J7 Pro must be on bootloader binary 5 or lower.

    This build uses bootloader binary 5. It can be flashed on a Samsung Galaxy J7 Pro running binary 5 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 9 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy J7 Pro

    No changelog details available.
    Model firmware by region