Samsung GT-N5100 N5100UBBMD1
GT-N5100 2 countries Android 4.2.1 (Jelly Bean)

Samsung GT-N5100 N5100UBBMD1 Firmware

Samsung GT-N5100 N5100UBBMD1 is an Android 4.2.1 (Jelly Bean) firmware for Paraguay (TGP), Uruguay (UFU). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build N5100ZABNH1: Android updated from Jelly(Android Bean) to Android 4.2.1 (Jelly Bean); bootloader binary raised from A (10) to B (11), so after installing it there is no way back to older builds. A newer build for GT-N5100 is available: N5100XXDNL5.

Download firmware
9.2/10 (479)8,636 times
Android 4.2.1 (Jelly Bean)
OS Version
2013-04-11
Build Date
2
Countries
2
CSC codes
B (11)
Bootloader binary

Bootloader binary B (11). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung GT-N5100 use bootloader binary X (33) (latest: N5100XXDNL5). If your device already runs binary X (33), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    ModelRegionCSC VersionMODEM/CP VersionRelease dateSizeFile nameDownload
    GT-N5100
    TGP Paraguay
    		N5100UWMBMD1N5100UBBMD1 — — — Download
    GT-N5100
    UFU Uruguay
    		N5100TFGBMD1N5100UBBMC7 2013-08-26 — — Download

    No matching downloads

    How to flash N5100UBBMD1

    • N5100UBBMD1 has bootloader binary B (11). Your device must run binary B (11) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of N5100UBBMD1 by region

    Samsung released this build in all regions (1) on the same day, August 26, 2013.

    Frequently Asked Questions

    N5100UBBMD1 is Android 4.2.1 (Jelly Bean) firmware for Samsung GT-N5100, released for Paraguay (TGP), Uruguay (UFU). Samsung built it on 2013-04-11.

    No. A newer build for GT-N5100 is available: N5100XXDNL5. Install it instead of N5100UBBMD1 unless you need this exact version. The previous build was N5100ZABNH1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung GT-N5100 must be on bootloader binary B (11) or lower.

    This build uses bootloader binary B (11). It can be flashed on a Samsung GT-N5100 running binary B (11) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 5 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung GT-N5100

    No changelog details available.
    Model firmware by region