GT-N8000 2 countries Android 4.4.2 (KitKat)

Samsung Galaxy Note 10.1 N8000XWALI4 Firmware

Name: Samsung Galaxy Note 10.1 (GT-N8000)
Brand: Samsung
Availability: InStock

Samsung Galaxy Note 10.1 N8000XWALI4 is an Android 4.4.2 (KitKat) firmware for Algeria (TMC), Egypt (EGY). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build N8000XWALG6, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for GT-N8000 is available: N8000XXCML2.

9.4/10 (470)11,058 times

Android 4.4.2 (KitKat)

OS Version

2012-09-13

First release

other regions until 2012-09-19

n/a

Security patch

Countries

CSC codes

W (32)

Bootloader binary

Bootloader binary W (32). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Note 10.1 use bootloader binary X (33) (latest: N8000XXCML2). If your device already runs binary X (33), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

Not sure which one to download?

Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.

MODEM/CP Version: N8000XXALI3

Model	Region	CSC Version	Build Date	Release date	Size	File name	Download
GT-N8000	EGY Egypt	N8000OJVALI2	2012-09-19	2012-10-31	—	—
GT-N8000	TMC Algeria	N8000OJVALI2	2012-09-13	2012-10-04	—	—

How to flash N8000XWALI4

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

N8000XWALI4 has bootloader binary W (32). Your device must run binary W (32) or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

N8000XWALI4 is Android 4.4.2 (KitKat) firmware for Samsung Galaxy Note 10.1, released for Algeria (TMC), Egypt (EGY). Samsung built it on 2012-09-13.

No. A newer build for GT-N8000 is available: N8000XXCML2. Install it instead of N8000XWALI4 unless you need this exact version. The previous build was N8000XWALG6.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Note 10.1 must be on bootloader binary W (32) or lower.

This build uses bootloader binary W (32). It can be flashed on a Samsung Galaxy Note 10.1 running binary W (32) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 1 other build of this model uses the same binary, so you can switch between them in both directions.