Samsung Galaxy Note 10.1 N8000XXUDOC1
GT-N8000 7 countries Android 4.4.2 (Jelly)

Samsung Galaxy Note 10.1 N8000XXUDOC1 Firmware

Samsung Galaxy Note 10.1 N8000XXUDOC1 is an Android 4.4.2 (Jelly) firmware for 7 countries, 7 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build N8000XXUDNL1: Android updated from Android 4.4.2 (KitKat) to Android 4.4.2 (Jelly). A newer build for GT-N8000 is available: N8000XXCML2.

Download firmware
9.1/10 (459)30,694 times
Android 4.4.2 (Jelly)
OS Version
2015-03-20
Build Date
7
Countries
7
CSC codes
U (30)
Bootloader binary

Bootloader binary U (30). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Note 10.1 use bootloader binary X (33) (latest: N8000XXCML2). If your device already runs binary X (33), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    ModelRegionCSC VersionMODEM/CP VersionBuild DateSizeFile nameDownload
    GT-N8000
    DRE Austria
    		N8000DOC1N8000XXUDOC1 2015-03-20 — — Download
    GT-N8000
    EUR Greece
    		N8000DOC1N8000XXUDOC1 2015-03-20 — — Download
    GT-N8000
    MOT Slovenia
    		N8000MOTDOC1N8000XXUDNH1 — — — Download
    GT-N8000
    PHN Netherlands
    		N8000PHNDOC1N8000XXUDNH1 — — — Download
    GT-N8000
    PRO Belgium
    		N8000DOC1N8000XXUDOC1 2015-03-20 — — Download
    GT-N8000
    SEB Baltic Europe
    		N8000SEBDOC1N8000XXUDNH1 — — — Download
    GT-N8000
    TIM Italy
    		N8000TIMDOC1N8000XXUDNH1 — — — Download

    No matching downloads

    How to flash N8000XXUDOC1

    • N8000XXUDOC1 has bootloader binary U (30). Your device must run binary U (30) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Frequently Asked Questions

    N8000XXUDOC1 is Android 4.4.2 (Jelly) firmware for Samsung Galaxy Note 10.1, released for 7 countries, 7 CSC codes. Samsung built it on 2015-03-20.

    No. A newer build for GT-N8000 is available: N8000XXCML2. Install it instead of N8000XXUDOC1 unless you need this exact version. The previous build was N8000XXUDNL1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Note 10.1 must be on bootloader binary U (30) or lower.

    This build uses bootloader binary U (30). It can be flashed on a Samsung Galaxy Note 10.1 running binary U (30) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 12 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Note 10.1

    No changelog details available.
    Model firmware by region