Samsung Galaxy Note 10.1 N8000XWALG6
GT-N8000 1 country Android 4.4.2 (KitKat)

Samsung Galaxy Note 10.1 N8000XWALG6 Firmware

Samsung Galaxy Note 10.1 N8000XWALG6 is an Android 4.4.2 (KitKat) firmware for New Zealand (VNZ). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build N8000XXUDPB1: Android updated from Android 4.4.2 (Jelly) to Android 4.4.2 (KitKat); bootloader binary raised from U (30) to W (32), so after installing it there is no way back to older builds. A newer build for GT-N8000 is available: N8000XXCML2.

Download firmware
9.4/10 (454)4,297 times
Android 4.4.2 (KitKat)
OS Version
n/a
Build Date
n/a
Security patch
1
Countries
1
CSC codes
W (32)
Bootloader binary

Bootloader binary W (32). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Note 10.1 use bootloader binary X (33) (latest: N8000XXCML2). If your device already runs binary X (33), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: N8000XXLGA
    ModelRegionCSC VersionSizeFile nameDownload
    GT-N8000
    VNZ New Zealand
    		N8000VNZALG2 — —

    No matching downloads

    How to flash N8000XWALG6

    • N8000XWALG6 has bootloader binary W (32). Your device must run binary W (32) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Frequently Asked Questions

    N8000XWALG6 is Android 4.4.2 (KitKat) firmware for Samsung Galaxy Note 10.1, released for New Zealand (VNZ).

    No. A newer build for GT-N8000 is available: N8000XXCML2. Install it instead of N8000XWALG6 unless you need this exact version. The previous build was N8000XXUDPB1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Note 10.1 must be on bootloader binary W (32) or lower.

    This build uses bootloader binary W (32). It can be flashed on a Samsung Galaxy Note 10.1 running binary W (32) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 1 other build of this model uses the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Note 10.1

    No changelog details available.
    Model firmware by region