Samsung Galaxy Note3 N9006ZCSGQD1
SM-N9006 1 country Android 5.0 (Lollipop)

Samsung Galaxy Note3 N9006ZCSGQD1 Firmware

Samsung Galaxy Note3 N9006ZCSGQD1 is an Android 5.0 (Lollipop) firmware for China (CHN). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build N9006ZNSGQD1: Android updated from Android 5.0 (KitKat) to Android 5.0 (Lollipop). A newer build for SM-N9006 is available: N9006ZCUGPA1.

Download firmware
8.8/10 (476)8,678 times
Android 5.0 (Lollipop)
OS Version
2017-04-17
First release
other regions until 2017-05-12
1
Countries
1
CSC codes
S (28)
Bootloader binary

Bootloader binary S (28). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Note3 use bootloader binary U (30) (latest: N9006ZCUGPA1). If your device already runs binary U (30), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: N9006ZCSGQD1
    ModelRegionCSC VersionBuild DateRelease dateSizeFile nameDownload
    SM-N9006
    CHN China
    		N9006CHNGQD1 2017-05-12 2017-05-12 1.287 GiB
    SM-N9006_1_20170511035913_z26ybrvbdy_fac.zip
    SM-N9006
    CHN China
    		N9006GQD1 2017-04-17 — — —

    No matching downloads

    How to flash N9006ZCSGQD1

    • N9006ZCSGQD1 has bootloader binary S (28). Your device must run binary S (28) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Display diagonal14.5 cm (5.7")
    • Display resolution1920 x 1080 pixels
    • Rear camera resolution13 MP
    • Rear camera typeSingle camera
    • Battery capacity3200 mAh
    • Weight168 g

    Specifications of SM-N900, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    N9006ZCSGQD1 is Android 5.0 (Lollipop) firmware for Samsung Galaxy Note3, released for China (CHN). Samsung built it on 2017-04-17.

    No. A newer build for SM-N9006 is available: N9006ZCUGPA1. Install it instead of N9006ZCSGQD1 unless you need this exact version. The previous build was N9006ZNSGQD1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 1.287 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Note3 must be on bootloader binary S (28) or lower.

    This build uses bootloader binary S (28). It can be flashed on a Samsung Galaxy Note3 running binary S (28) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 1 other build of this model uses the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Note3

    No changelog details available.
    Model firmware by region