Samsung Galaxy Note3 N9006ZNUGOC3
SM-N9006 1 country Android 5.0 (KitKat)

Samsung Galaxy Note3 N9006ZNUGOC3 Firmware

Samsung Galaxy Note3 N9006ZNUGOC3 is an Android 5.0 (KitKat) firmware for China (CHU). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build N9006ZCUFOA4: Android updated from Android 4.4.2 (KitKat) to Android 5.0 (KitKat). A newer build for SM-N9006 is available: N9006ZCUGPA1.

Download firmware
9.0/10 (458)4,347 times
Android 5.0 (KitKat)
OS Version
2015-03-14
Build Date
1
Countries
1
CSC codes
U (30)
Bootloader binary

Bootloader binary U (30). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: N9006ZNUGOC3
    ModelRegionCSC VersionSizeFile nameDownload
    SM-N9006
    CHU China
    		N9006GOC3 — — Download

    No matching downloads

    How to flash N9006ZNUGOC3

    • N9006ZNUGOC3 has bootloader binary U (30). Your device must run binary U (30) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Display diagonal14.5 cm (5.7")
    • Display resolution1920 x 1080 pixels
    • Rear camera resolution13 MP
    • Rear camera typeSingle camera
    • Battery capacity3200 mAh
    • Weight168 g

    Specifications of SM-N900, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    N9006ZNUGOC3 is Android 5.0 (KitKat) firmware for Samsung Galaxy Note3, released for China (CHU). Samsung built it on 2015-03-14.

    No. A newer build for SM-N9006 is available: N9006ZCUGPA1. Install it instead of N9006ZNUGOC3 unless you need this exact version. The previous build was N9006ZCUFOA4.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Note3 must be on bootloader binary U (30) or lower.

    This build uses bootloader binary U (30). It can be flashed on a Samsung Galaxy Note3 running binary U (30) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 18 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Note3

    No changelog details available.
    Model firmware by region