SM-N900W8 1 country Android 5.0 (Jelly)

Samsung Galaxy Note3 N900W8UBU2DPG1 Firmware

Name: Samsung Galaxy Note3 (SM-N900W8)
Brand: Samsung
Availability: InStock

Samsung Galaxy Note3 N900W8UBU2DPG1 is an Android 5.0 (Jelly) firmware for Argentina (ANC). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build N900W8VLU2DPG1 https://samfirm.shop/build/N900W8VLU2DPG1: Android updated from Android 5.0 (Lollipop) to Android 5.0 (Jelly). A newer build for SM-N900W8 is available: N900W8UBUCNJ1 https://samfirm.shop/build/N900W8UBUCNJ1.

9.2/10 (32)4,606 times

Android 5.0 (Jelly)

OS Version

2016-07-04

First release

other regions until 2016-08-04

n/a

Security patch

Countries

CSC codes

Bootloader binary

Bootloader binary 2. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Note3 use bootloader binary U (30) (latest: N900W8UBUCNJ1). If your device already runs binary U (30), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

Model	Region	CSC Version	MODEM/CP Version	Build Date	Release date	Size	File name	Download
SM-N900W8	ANC Argentina	N900W8ANCDPG1	N900W8UBU2DPC2	2016-08-04	2016-08-26	1.308 GiB	SM-N900W8_1_20160804150114_bn6ow7vjcz_fac.zip
SM-N900W8	ANC Argentina	N900W8DPG1	N900W8UBU2DPG1	2016-07-04	—	—	—

Device specifications

Display diagonal14.5 cm (5.7")
Display resolution1920 x 1080 pixels
Rear camera resolution13 MP
Rear camera typeSingle camera
Battery capacity3200 mAh
Weight168 g

Specifications of SM-N900, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

How to flash N900W8UBU2DPG1

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

N900W8UBU2DPG1 has bootloader binary 2. Your device must run binary 2 or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

N900W8UBU2DPG1 is Android 5.0 (Jelly) firmware for Samsung Galaxy Note3, released for Argentina (ANC). Samsung built it on 2016-07-04.

No. A newer build for SM-N900W8 is available: N900W8UBUCNJ1. Install it instead of N900W8UBU2DPG1 unless you need this exact version. The previous build was N900W8VLU2DPG1.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 1.308 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Note3 must be on bootloader binary 2 or lower.

This build uses bootloader binary 2. It can be flashed on a Samsung Galaxy Note3 running binary 2 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 16 other builds of this model use the same binary, so you can switch between them in both directions.