Samsung Galaxy Note3 N900W8UBUBMI6
SM-N900W8 2 countries

Samsung Galaxy Note3 N900W8UBUBMI6 Firmware

Samsung Galaxy Note3 N900W8UBUBMI6 is an Android firmware for Argentina (ANC), Uruguay (UFU). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build N900W8UBS2DRJ1: bootloader binary raised from 2 to U (30), so after installing it there is no way back to older builds. A newer build for SM-N900W8 is available: N900W8UBUCNJ1.

Download firmware
9.3/10 (480)8,446 times
2013-09-11
Build Date
2
Countries
2
CSC codes
U (30)
Bootloader binary

Bootloader binary U (30). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: N900W8UBUBMI5
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-N900W8
    ANC Argentina
    		N900W8ANCBMI4 2013-09-27 1.309 GiB
    SM-N900W8_1_20181115094001_xs16gmh896_fac.zip
    		Download
    SM-N900W8
    UFU Uruguay
    		N900W8TFGBMI4 2013-09-27 1.361 GiB
    SM-N900W8_1_20160130132414_k707jv5ktm_fac.zip
    		Download

    No matching downloads

    How to flash N900W8UBUBMI6

    • N900W8UBUBMI6 has bootloader binary U (30). Your device must run binary U (30) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of N900W8UBUBMI6 by region

    Samsung released this build in all regions (2) on the same day, September 27, 2013.

    Device specifications

    • Display diagonal14.5 cm (5.7")
    • Display resolution1920 x 1080 pixels
    • Rear camera resolution13 MP
    • Rear camera typeSingle camera
    • Battery capacity3200 mAh
    • Weight168 g

    Specifications of SM-N900, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    No. A newer build for SM-N900W8 is available: N900W8UBUCNJ1. Install it instead of N900W8UBUBMI6 unless you need this exact version. The previous build was N900W8UBS2DRJ1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Note3 must be on bootloader binary U (30) or lower.

    This build uses bootloader binary U (30). It can be flashed on a Samsung Galaxy Note3 running binary U (30) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 9 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Note3

    No changelog details available.
    Model firmware by region