Samsung Galaxy Note3 N900W8UBUBMJ1
SM-N900W8 3 countries

Samsung Galaxy Note3 N900W8UBUBMJ1 Firmware

Samsung Galaxy Note3 N900W8UBUBMJ1 is an Android firmware for Paraguay (CTP), Puerto Rico (PCT), Uruguay (CTU). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build N900W8UBUBMI6, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-N900W8 is available: N900W8UBUCNJ1.

Download firmware
9.3/10 (478)13,127 times
2013-10-01
Build Date
3
Countries
3
CSC codes
U (30)
Bootloader binary

Bootloader binary U (30). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: N900W8UBUBMJ1
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-N900W8
    CTP Paraguay
    		N900W8UWABMI4 2013-10-30 — — Download
    SM-N900W8
    CTU Uruguay
    		N900W8UWABMI4 2013-10-30 1.351 GiB
    SM-N900W8_1_20181123073340_ta0ryu1brc_fac.zip
    		Download
    SM-N900W8
    PCT Puerto Rico
    		N900W8UWABMI4 2013-11-09 1.344 GiB
    SM-N900W8_1_20181115093840_teqbsan7ey_fac.zip
    		Download

    No matching downloads

    How to flash N900W8UBUBMJ1

    • N900W8UBUBMJ1 has bootloader binary U (30). Your device must run binary U (30) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of N900W8UBUBMJ1 by region

    First release
    October 30, 2013
    Last region
    November 9, 2013
    Duration
    11 days
    Regions
    3
    1. Day 1 · · 2 regions
      ParaguayCTPUruguayCTU
    2. Day 11 · · 1 region
      Puerto RicoPCT

    Device specifications

    • Display diagonal14.5 cm (5.7")
    • Display resolution1920 x 1080 pixels
    • Rear camera resolution13 MP
    • Rear camera typeSingle camera
    • Battery capacity3200 mAh
    • Weight168 g

    Specifications of SM-N900, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    No. A newer build for SM-N900W8 is available: N900W8UBUCNJ1. Install it instead of N900W8UBUBMJ1 unless you need this exact version. The previous build was N900W8UBUBMI6.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Note3 must be on bootloader binary U (30) or lower.

    This build uses bootloader binary U (30). It can be flashed on a Samsung Galaxy Note3 running binary U (30) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 9 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Note3

    No changelog details available.
    Model firmware by region