Samsung Galaxy Note4 N910GDTU1DPE3
SM-N910G 3 countries Android 6.0.1 (Marshmallow)

Samsung Galaxy Note4 N910GDTU1DPE3 Firmware

Samsung Galaxy Note4 N910GDTU1DPE3 is an Android 6.0.1 (Marshmallow) firmware for Bangladesh (BNG), India (INS, INU), Sri Lanka (SLK). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build N910GDTU1DPE1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-N910G is available: N910GDTS1DRH2.

Download firmware
9.3/10 (459)17,038 times
Android 6.0.1 (Marshmallow)
OS Version
2016-05-10
Build Date
3
Countries
4
CSC codes
1
Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: N910GDTU1DPE3
    ModelRegionCSC VersionSizeFile nameDownload
    SM-N910G
    BNG Bangladesh
    		N910GODD1DPE2 — — Download
    SM-N910G
    INS India
    		N910GODD1DPE2 — — Download
    SM-N910G
    INU India
    		N910GODD1DPE2 — — Download
    SM-N910G
    SLK Sri Lanka
    		N910GODD1DPE2 — — Download

    No matching downloads

    How to flash N910GDTU1DPE3

    • N910GDTU1DPE3 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Display diagonal14.5 cm (5.7")
    • Display resolution2560 x 1440 pixels
    • Display typeSAMOLED
    • RAM3 GB
    • Rear camera resolution16 MP
    • Rear camera typeSingle camera
    • Battery capacity3220 mAh
    • Weight175 g

    Specifications of SM-N9100, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    N910GDTU1DPE3 is Android 6.0.1 (Marshmallow) firmware for Samsung Galaxy Note4, released for Bangladesh (BNG), India (INS, INU), Sri Lanka (SLK). Samsung built it on 2016-05-10.

    No. A newer build for SM-N910G is available: N910GDTS1DRH2. Install it instead of N910GDTU1DPE3 unless you need this exact version. The previous build was N910GDTU1DPE1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Note4 must be on bootloader binary 1 or lower.

    This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy Note4 running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 67 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Note4

    No changelog details available.
    Model firmware by region