Samsung Galaxy Note Edge N915FXXS1DPF2
SM-N915F 5 countries Android 6.0.1 (Lollipop)

Samsung Galaxy Note Edge N915FXXS1DPF2 Firmware

Samsung Galaxy Note Edge N915FXXS1DPF2 is an Android 6.0.1 (Lollipop) firmware for 5 countries, 5 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build N915FXXU1DPF1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-N915F is available: N915FXXS1DRI3.

Download firmware
9.0/10 (460)21,914 times
Android 6.0.1 (Lollipop)
OS Version
2016-06-03
Build Date
5
Countries
5
CSC codes
1
Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: N915FXXS1DPF2
    ModelRegionCSC VersionSizeFile nameDownload
    SM-N915F
    CAM Cambodia
    		N915FOLC1DPE1 — — Download
    SM-N915F
    THL Thailand
    		N915FOLC1DPE1 — — Download
    SM-N915F
    XEV Vietnam
    		N915FOLC1DPE1 — — Download
    SM-N915F
    XME Malaysia
    		N915FOLC1DPE1 — — Download
    SM-N915F
    XSE Indonesia
    		N915FOLC1DPE1 — — Download

    No matching downloads

    How to flash N915FXXS1DPF2

    • N915FXXS1DPF2 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Display diagonal14.2 cm (5.6")
    • Display resolution2560 x 1440 pixels
    • Display typeSAMOLED
    • Processor frequency2.7 GHz
    • RAM3 GB
    • Rear camera resolution16 MP
    • Rear camera typeSingle camera
    • SIM cardsSingle SIM
    • Battery capacity3000 mAh
    • Weight174 g

    Frequently Asked Questions

    N915FXXS1DPF2 is Android 6.0.1 (Lollipop) firmware for Samsung Galaxy Note Edge, released for 5 countries, 5 CSC codes. Samsung built it on 2016-06-03.

    No. A newer build for SM-N915F is available: N915FXXS1DRI3. Install it instead of N915FXXS1DPF2 unless you need this exact version. The previous build was N915FXXU1DPF1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Note Edge must be on bootloader binary 1 or lower.

    This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy Note Edge running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 104 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Note Edge

    No changelog details available.
    Model firmware by region