Samsung Galaxy Note7 N930FXXU1APGG
SM-N930F 1 country Android 6.0.1

Samsung Galaxy Note7 N930FXXU1APGG Firmware

Samsung Galaxy Note7 N930FXXU1APGG is an Android 6.0.1 firmware for Australia (OPS). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build N930FXXU1APGB: Android updated from Android 6.0.1 (Marshmallow) to Android 6.0.1. A newer build for SM-N930F is available: N930FXXU3BQA1.

Download firmware
9.1/10 (460)4,259 times
Android 6.0.1
OS Version
2016-07-15
Build Date
1
Countries
1
CSC codes
1
Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Note7 use bootloader binary 3 (latest: N930FXXU3BQA1). If your device already runs binary 3, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: N930FXXU1APGG
    ModelRegionCSC VersionSizeFile nameDownload
    SM-N930F
    OPS Australia
    		N930F1APG7 — — Download

    No matching downloads

    How to flash N930FXXU1APGG

    • N930FXXU1APGG has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid 6.0
    • Display diagonal14.5 cm (5.7")
    • Display resolution2560 x 1440 pixels
    • Display typeSAMOLED
    • Processor frequency2.3 GHz
    • RAM4 GB
    • RAM typeLPDDR4
    • Rear camera resolution12 MP
    • Rear camera typeSingle camera
    • Battery capacity3500 mAh
    • Weight169 g

    Frequently Asked Questions

    N930FXXU1APGG is Android 6.0.1 firmware for Samsung Galaxy Note7, released for Australia (OPS). Samsung built it on 2016-07-15.

    No. A newer build for SM-N930F is available: N930FXXU3BQA1. Install it instead of N930FXXU1APGG unless you need this exact version. The previous build was N930FXXU1APGB.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Note7 must be on bootloader binary 1 or lower.

    This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy Note7 running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 9 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Note7

    No changelog details available.
    Model firmware by region