Samsung Galaxy Note9 N960NKSU3DSLC
SM-N960N 1 country Android 10

Samsung Galaxy Note9 N960NKSU3DSLC Firmware

Samsung Galaxy Note9 N960NKSU3DSLC is an Android 10 firmware for South Korea (KOO, KTC, LUC, SKC). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build N960NKSU3CSJ1: Android updated from Android 9 (Pie) to Android 10. A newer build for SM-N960N is available: N960NKSU3FVG4.

Download firmware
8.7/10 (479)17,472 times
Android 10
OS Version
2019-12-26
First release
other regions until 2019-12-27
1
Countries
4
CSC codes
3
Bootloader binary

Bootloader binary 3. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    ModelRegionCSC VersionMODEM/CP VersionBuild DateRelease dateSizeFile nameDownload
    SM-N960N
    KOO South Korea
    		N960NOKR3DSLCN960NKOU3DSLA 2019-12-27 2020-01-13 4.25 GiB
    SM-N960N_2_20220801104440_zptckf0f88_fac.zip
    		Download
    SM-N960N
    KTC South Korea
    		N960NOKR3DSLCN960NKSU3DSLC 2019-12-26 — — — Download
    SM-N960N
    LUC South Korea
    		N960NOKR3DSLCN960NKOU3DSLA 2019-12-27 2020-01-13 4.691 GiB
    SM-N960N_2_20220801112450_ztote9mnx8_fac.zip
    		Download
    SM-N960N
    SKC South Korea
    		N960NOKR3DSLCN960NKOU3DSLA 2019-12-27 2020-01-13 4.497 GiB
    SM-N960N_2_20220801121740_2hwp0s4gzh_fac.zip
    		Download

    No matching downloads

    How to flash N960NKSU3DSLC

    • N960NKSU3DSLC has bootloader binary 3. Your device must run binary 3 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of N960NKSU3DSLC by region

    Samsung released this build in all regions (3) on the same day, January 13, 2020.

    Device specifications

    • Launched withAndroid 8.1
    • Display diagonal16.3 cm (6.4")
    • Display resolution2960 x 1440 pixels
    • Display typeSAMOLED
    • RAM8 GB
    • RAM typeLPDDR4
    • Rear camera resolution12 MP
    • Rear camera typeDual camera
    • Battery capacity4000 mAh
    • Weight201 g

    Specifications of SM-N960F, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    N960NKSU3DSLC is Android 10 firmware for Samsung Galaxy Note9, released for South Korea (KOO, KTC, LUC, SKC). Samsung built it on 2019-12-26.

    No. A newer build for SM-N960N is available: N960NKSU3FVG4. Install it instead of N960NKSU3DSLC unless you need this exact version. The previous build was N960NKSU3CSJ1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Note9 must be on bootloader binary 3 or lower.

    This build uses bootloader binary 3. It can be flashed on a Samsung Galaxy Note9 running binary 3 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 16 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Note9

    No changelog details available.
    Model firmware by region