GT-P1000 2 countries Android 2.3.3 (Gingerbread)

Samsung Galaxy Tab (3G + WiFi) P1000DDJPA Firmware

Name: Samsung Galaxy Tab (3G + WiFi) (GT-P1000)
Brand: Samsung
Availability: InStock

Samsung Galaxy Tab (3G + WiFi) P1000DDJPA is an Android 2.3.3 (Gingerbread) firmware for India (INU), TML. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build P1000BVJM8 https://samfirm.shop/build/P1000BVJM8: Android updated from Android 2.2 (Froyo) to Android 2.3.3 (Gingerbread); bootloader binary raised from B (11) to D (13), so after installing it there is no way back to older builds. A newer build for GT-P1000 is available: P1000ZHJQ5 https://samfirm.shop/build/P1000ZHJQ5.

9.3/10 (471)8,768 times

Android 2.3.3 (Gingerbread)

OS Version

2011-06-14

Build Date

n/a

Security patch

Countries

CSC codes

D (13)

Bootloader binary

Bootloader binary D (13). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Tab (3G + WiFi) use bootloader binary Z (35) (latest: P1000ZHJQ5). If your device already runs binary Z (35), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

MODEM/CP Version: ODDJPA

Model	Region	CSC Version	Size	File name	Download
GT-P1000	INU India	DDJP4	—	—
GT-P1000	TML	DDJP4	—	—

How to flash P1000DDJPA

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

P1000DDJPA has bootloader binary D (13). Your device must run binary D (13) or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

P1000DDJPA is Android 2.3.3 (Gingerbread) firmware for Samsung Galaxy Tab (3G + WiFi), released for India (INU), TML. Samsung built it on 2011-06-14.

No. A newer build for GT-P1000 is available: P1000ZHJQ5. Install it instead of P1000DDJPA unless you need this exact version. The previous build was P1000BVJM8.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Tab (3G + WiFi) must be on bootloader binary D (13) or lower.

This build uses bootloader binary D (13). It can be flashed on a Samsung Galaxy Tab (3G + WiFi) running binary D (13) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 3 other builds of this model use the same binary, so you can switch between them in both directions.