GT-P1000 3 countries Android 2.3.6 (Gingerbread)

Samsung Galaxy Tab (3G + WiFi) P1000XWJQ8 Firmware

Name: Samsung Galaxy Tab (3G + WiFi) (GT-P1000)
Brand: Samsung
Availability: InStock

Samsung Galaxy Tab (3G + WiFi) P1000XWJQ8 is an Android 2.3.6 (Gingerbread) firmware for Austria (ATO), Czechia (XEZ), Switzerland (AUT). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build P1000XWJPJ: Android updated from Android 2.3.3 (Gingerbread) to Android 2.3.6 (Gingerbread). A newer build for GT-P1000 is available: P1000ZHJQ5.

9.0/10 (470)13,142 times

Android 2.3.6 (Gingerbread)

OS Version

2011-11-16

Build Date

n/a

Security patch

Countries

CSC codes

X (33)

Bootloader binary

Bootloader binary X (33). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Tab (3G + WiFi) use bootloader binary Z (35) (latest: P1000ZHJQ5). If your device already runs binary Z (35), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

Not sure which one to download?

Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.

MODEM/CP Version: P1000XXJPZ

Model	Region	CSC Version	Size	File name
GT-P1000	ATO Austria	P1000ATOJQ1	—	—
GT-P1000	AUT Switzerland	P1000AUTJQ1	—	—
GT-P1000	XEZ Czechia	P1000XEZJQ2	—	—

How to flash P1000XWJQ8

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

P1000XWJQ8 has bootloader binary X (33). Your device must run binary X (33) or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

P1000XWJQ8 is Android 2.3.6 (Gingerbread) firmware for Samsung Galaxy Tab (3G + WiFi), released for Austria (ATO), Czechia (XEZ), Switzerland (AUT). Samsung built it on 2011-11-16.

No. A newer build for GT-P1000 is available: P1000ZHJQ5. Install it instead of P1000XWJQ8 unless you need this exact version. The previous build was P1000XWJPJ.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Tab (3G + WiFi) must be on bootloader binary X (33) or lower.

This build uses bootloader binary X (33). It can be flashed on a Samsung Galaxy Tab (3G + WiFi) running binary X (33) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 9 other builds of this model use the same binary, so you can switch between them in both directions.