Samsung Galaxy Tab (3G + WiFi) P1000DXJPI
GT-P1000 2 countries Android 2.3.3 (Gingerbread)

Samsung Galaxy Tab (3G + WiFi) P1000DXJPI Firmware

Samsung Galaxy Tab (3G + WiFi) P1000DXJPI is an Android 2.3.3 (Gingerbread) firmware for Thailand (THL), Vietnam (XEV). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build P1000DXJPD, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for GT-P1000 is available: P1000ZHJQ5.

Download firmware
9.0/10 (475)8,563 times
Android 2.3.3 (Gingerbread)
OS Version
2011-07-24
Build Date
2
Countries
2
CSC codes
D (13)
Bootloader binary

Bootloader binary D (13). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Tab (3G + WiFi) use bootloader binary Z (35) (latest: P1000ZHJQ5). If your device already runs binary Z (35), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: P1000OLBJPH
    ModelRegionCSC VersionSizeFile nameDownload
    GT-P1000
    THL Thailand
    		P1000DXJPE — —
    GT-P1000
    XEV Vietnam
    		P1000DXJPE — —

    No matching downloads

    How to flash P1000DXJPI

    • P1000DXJPI has bootloader binary D (13). Your device must run binary D (13) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Frequently Asked Questions

    P1000DXJPI is Android 2.3.3 (Gingerbread) firmware for Samsung Galaxy Tab (3G + WiFi), released for Thailand (THL), Vietnam (XEV). Samsung built it on 2011-07-24.

    No. A newer build for GT-P1000 is available: P1000ZHJQ5. Install it instead of P1000DXJPI unless you need this exact version. The previous build was P1000DXJPD.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Tab (3G + WiFi) must be on bootloader binary D (13) or lower.

    This build uses bootloader binary D (13). It can be flashed on a Samsung Galaxy Tab (3G + WiFi) running binary D (13) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 3 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Tab (3G + WiFi)

    No changelog details available.
    Model firmware by region