Samsung Galaxy Tab 2 7.0 WiFi P3110ZSCLK5
GT-P3110 1 country

Samsung Galaxy Tab 2 7.0 WiFi P3110ZSCLK5 Firmware

Samsung Galaxy Tab 2 7.0 WiFi P3110ZSCLK5 is an Android firmware for Taiwan (BRI). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build P3110ZSBLK2, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for GT-P3110 is available: P3110XXDNE4.

Download firmware
9.2/10 (474)4,397 times
n/a
OS Version
2012-11-28
Build Date
n/a
Security patch
1
Countries
1
CSC codes
S (28)
Bootloader binary

Bootloader binary S (28). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Tab 2 7.0 WiFi use bootloader binary X (33) (latest: P3110XXDNE4). If your device already runs binary X (33), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: P3110ZSCLK5
    ModelRegionCSC VersionSizeFile nameDownload
    GT-P3110
    BRI Taiwan
    		P3110BRICLK5 741.554 MiB
    GT-P3110_1_20151124115752_0ppqpxyga2_fac.zip

    No matching downloads

    How to flash P3110ZSCLK5

    • P3110ZSCLK5 has bootloader binary S (28). Your device must run binary S (28) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid
    • Display diagonal17.8 cm (7")
    • Display resolution1024 x 600 pixels
    • Processor frequency1 GHz
    • Rear camera resolution3.2 MP
    • Rear camera typeSingle camera
    • Front camera resolution0.3 MP
    • Wi-Fi standardWi-Fi 4 (802.11n)
    • Weight345 g

    Frequently Asked Questions

    No. A newer build for GT-P3110 is available: P3110XXDNE4. Install it instead of P3110ZSCLK5 unless you need this exact version. The previous build was P3110ZSBLK2.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 741.554 MiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Tab 2 7.0 WiFi must be on bootloader binary S (28) or lower.

    This build uses bootloader binary S (28). It can be flashed on a Samsung Galaxy Tab 2 7.0 WiFi running binary S (28) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 2 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Tab 2 7.0 WiFi

    No changelog details available.
    Model firmware by region