Samsung Galaxy Note 10.1 2014 Edition P600UBUCNH2 Firmware
Samsung Galaxy Note 10.1 2014 Edition P600UBUCNH2 is an Android 4.4.2 (KitKat) firmware for 5 countries, 6 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build P600ZHUCNH1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-P600 is available: P600UEUDQF1.
9.4/10 (470)25,982 times
Android 4.4.2 (KitKat)
OS Version
2014-08-27
Build Date
n/a
Security patch
5
Countries
6
CSC codes
U (30)
Bootloader binary
Bootloader binary U (30). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.
All regional downloads
Pick your region (CSC) to download the matching firmware package.
Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
MODEM/CP Version: P600UBUCNH2
Device specifications
- Launched withAndroid
- Display diagonal25.6 cm (10.1")
- Display resolution2560 x 1600 pixels
- Processor frequency1.9 GHz
- Rear camera resolution8 MP
- Rear camera typeSingle camera
- Front camera resolution2 MP
- Wi-Fi standardWi-Fi 5 (802.11ac)
- Weight540 g
How to flash P600UBUCNH2
- Install Samsung USB Drivers:Download Official Drivers
- Download Odin Flash Tool:
- P600UBUCNH2 has bootloader binary U (30). Your device must run binary U (30) or lower: it is the 5th character from the end of your current build number.
- CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
- HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
- The Download Mode key combo depends on the model: see all combos.
Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.
Frequently Asked Questions
P600UBUCNH2 is Android 4.4.2 (KitKat) firmware for Samsung Galaxy Note 10.1 2014 Edition, released for 5 countries, 6 CSC codes. Samsung built it on 2014-08-27.
No. A newer build for SM-P600 is available: P600UEUDQF1. Install it instead of P600UBUCNH2 unless you need this exact version. The previous build was P600ZHUCNH1.
Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 1.379 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Note 10.1 2014 Edition must be on bootloader binary U (30) or lower.
This build uses bootloader binary U (30). It can be flashed on a Samsung Galaxy Note 10.1 2014 Edition running binary U (30) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 46 other builds of this model use the same binary, so you can switch between them in both directions.