Samsung Galaxy Tab 7.0 Plus P6200XXME1
GT-P6200 3 countries Android 3.2 (Honeycomb)

Samsung Galaxy Tab 7.0 Plus P6200XXME1 Firmware

Samsung Galaxy Tab 7.0 Plus P6200XXME1 is an Android 3.2 (Honeycomb) firmware for Indonesia (XSE), Philippines (SMA), Singapore (STH, XSP). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build P6200XXMD6: Android updated from Jelly(Android Bean) to Android 3.2 (Honeycomb). A newer build for GT-P6200 is available: P6200XXMF1.

Download firmware
8.9/10 (477)17,131 times
Android 3.2 (Honeycomb)
OS Version
2013-05-17
First release
other regions until 2013-05-21
3
Countries
4
CSC codes
X (33)
Bootloader binary

Bootloader binary X (33). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: P6200XXMC3
    ModelRegionCSC VersionBuild DateSizeFile nameDownload
    GT-P6200
    SMA Philippines
    		P6200OLBME1 2013-05-17 — — Download
    GT-P6200
    STH Singapore
    		P6200OLBME1 2013-05-21 — — Download
    GT-P6200
    XSE Indonesia
    		P6200OLBME1 — — — Download
    GT-P6200
    XSP Singapore
    		P6200OLBME1 2013-05-21 — — Download

    No matching downloads

    How to flash P6200XXME1

    • P6200XXME1 has bootloader binary X (33). Your device must run binary X (33) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Frequently Asked Questions

    P6200XXME1 is Android 3.2 (Honeycomb) firmware for Samsung Galaxy Tab 7.0 Plus, released for Indonesia (XSE), Philippines (SMA), Singapore (STH, XSP). Samsung built it on 2013-05-17.

    No. A newer build for GT-P6200 is available: P6200XXMF1. Install it instead of P6200XXME1 unless you need this exact version. The previous build was P6200XXMD6.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Tab 7.0 Plus must be on bootloader binary X (33) or lower.

    This build uses bootloader binary X (33). It can be flashed on a Samsung Galaxy Tab 7.0 Plus running binary X (33) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 8 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Tab 7.0 Plus

    No changelog details available.
    Model firmware by region