Samsung Galaxy Tab 7.7 P6800JPLPC
GT-P6800 4 countries Android 3.2 (Honeycomb)

Samsung Galaxy Tab 7.7 P6800JPLPC Firmware

Samsung Galaxy Tab 7.7 P6800JPLPC is an Android 3.2 (Honeycomb) firmware for 4 countries, 5 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build P6800JPLPA: Android updated from Ice(Android Cream) to Android 3.2 (Honeycomb). A newer build for GT-P6800 is available: P6800ZSMK1.

Download firmware
8.7/10 (455)21,479 times
Android 3.2 (Honeycomb)
OS Version
4
Countries
5
CSC codes
J (19)
Bootloader binary

Bootloader binary J (19). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Tab 7.7 use bootloader binary Z (35) (latest: P6800ZSMK1). If your device already runs binary Z (35), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: P6800XXLPW
    ModelRegionCSC VersionSizeFile nameDownload
    GT-P6800
    EGY Egypt
    		P6800OJPLP7 — —
    GT-P6800
    JED Saudi Arabia
    		P6800OJPLP7 — —
    GT-P6800
    KSA Saudi Arabia
    		P6800OJPLP7 — —
    GT-P6800
    MID Iraq
    		P6800OJPLP7 — —
    GT-P6800
    XSG United Arab Emirates
    		P6800OJPLP7 — —

    No matching downloads

    How to flash P6800JPLPC

    • P6800JPLPC has bootloader binary J (19). Your device must run binary J (19) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Frequently Asked Questions

    P6800JPLPC is Android 3.2 (Honeycomb) firmware for Samsung Galaxy Tab 7.7, released for 4 countries, 5 CSC codes.

    No. A newer build for GT-P6800 is available: P6800ZSMK1. Install it instead of P6800JPLPC unless you need this exact version. The previous build was P6800JPLPA.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Tab 7.7 must be on bootloader binary J (19) or lower.

    This build uses bootloader binary J (19). It can be flashed on a Samsung Galaxy Tab 7.7 running binary J (19) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 2 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Tab 7.7

    No changelog details available.
    Model firmware by region