Samsung Galaxy Tab 10.1 P7500XWMPI
GT-P7500 3 countries Android 3.2 (Honeycomb)

Samsung Galaxy Tab 10.1 P7500XWMPI Firmware

Samsung Galaxy Tab 10.1 P7500XWMPI is an Android 3.2 (Honeycomb) firmware for Italy (HUI), NSE, Norway (TEN). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build P7500XWMPH: Android updated from Ice(Android Cream) to Android 3.2 (Honeycomb). A newer build for GT-P7500 is available: P7500ZSLP8.

9.1/10 (473)17,227 times
Android 3.2 (Honeycomb)
OS Version
2013-01-17
Build Date
n/a
Security patch
3
Countries
3
CSC codes
X (33)
Bootloader binary

Bootloader binary X (33). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Tab 10.1 use bootloader binary Z (35) (latest: P7500ZSLP8). If your device already runs binary Z (35), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    ModelRegionCSC VersionMODEM/CP VersionBuild DateRelease dateSizeFile nameDownload
    GT-P7500
    HUI Italy
    		P7500NELP3P7500HUILP4 2013-01-17 — — —
    GT-P7500
    NSE
    		P7500OXXMP9P7500XXLQ8 2013-01-17 2013-03-14 — —
    GT-P7500
    TEN Norway
    		P7500XXLQ8P7500TENMA1 2013-01-17 — — —
    GT-P7500
    TEN Norway
    		P7500TENMA1P7500XXLQ8 — 2013-04-05 — —

    No matching downloads

    How to flash P7500XWMPI

    • P7500XWMPI has bootloader binary X (33). Your device must run binary X (33) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of P7500XWMPI by region

    First release
    March 14, 2013
    Last region
    April 5, 2013
    Duration
    23 days
    Regions
    2
    1. Day 1 · · 1 region
      NSE
    2. Day 23 · · 1 region
      NorwayTEN

    Frequently Asked Questions

    P7500XWMPI is Android 3.2 (Honeycomb) firmware for Samsung Galaxy Tab 10.1, released for Italy (HUI), NSE, Norway (TEN). Samsung built it on 2013-01-17.

    No. A newer build for GT-P7500 is available: P7500ZSLP8. Install it instead of P7500XWMPI unless you need this exact version. The previous build was P7500XWMPH.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Tab 10.1 must be on bootloader binary X (33) or lower.

    This build uses bootloader binary X (33). It can be flashed on a Samsung Galaxy Tab 10.1 running binary X (33) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 20 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Tab 10.1

    No changelog details available.
    Model firmware by region