GT-P7500 2 countries Android 3.1 (Honeycomb)

Samsung Galaxy Tab 10.1 P7500XWLP3 Firmware

Name: Samsung Galaxy Tab 10.1 (GT-P7500)
Brand: Samsung
Availability: InStock

Samsung Galaxy Tab 10.1 P7500XWLP3 is an Android 3.1 (Honeycomb) firmware for Bahrain (ARB), TML. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build P7500XWLP2 https://samfirm.shop/build/P7500XWLP2: Android updated from Ice(Android Cream) to Android 3.1 (Honeycomb). A newer build for GT-P7500 is available: P7500ZSLP8 https://samfirm.shop/build/P7500ZSLP8.

9.0/10 (452)8,618 times

Android 3.1 (Honeycomb)

OS Version

n/a

Build Date

n/a

Security patch

Countries

CSC codes

X (33)

Bootloader binary

Bootloader binary X (33). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Tab 10.1 use bootloader binary Z (35) (latest: P7500ZSLP8). If your device already runs binary Z (35), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

MODEM/CP Version: P7500XXLQ8

Model	Region	CSC Version	Size	File name	Download
GT-P7500	ARB Bahrain	P7500OJVLP5	—	—
GT-P7500	TML	P7500ODDLP4	—	—

How to flash P7500XWLP3

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

P7500XWLP3 has bootloader binary X (33). Your device must run binary X (33) or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

P7500XWLP3 is Android 3.1 (Honeycomb) firmware for Samsung Galaxy Tab 10.1, released for Bahrain (ARB), TML.

No. A newer build for GT-P7500 is available: P7500ZSLP8. Install it instead of P7500XWLP3 unless you need this exact version. The previous build was P7500XWLP2.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Tab 10.1 must be on bootloader binary X (33) or lower.

This build uses bootloader binary X (33). It can be flashed on a Samsung Galaxy Tab 10.1 running binary X (33) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 20 other builds of this model use the same binary, so you can switch between them in both directions.