Samsung Galaxy Note Pro 12.2 P905XXUABOD7
SM-P905 2 countries Android 5.0.2 (KitKat)

Samsung Galaxy Note Pro 12.2 P905XXUABOD7 Firmware

Samsung Galaxy Note Pro 12.2 P905XXUABOD7 is an Android 5.0.2 (KitKat) firmware for Italy (ITV), Switzerland (AUT). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build P905ZSU1BPA3: Android updated from Android 5.0.2 (Lollipop) to Android 5.0.2 (KitKat); bootloader binary raised from 1 to A (10), so after installing it there is no way back to older builds. A newer build for SM-P905 is available: P905XXUBML3.

Download firmware
9.2/10 (461)8,870 times
Android 5.0.2 (KitKat)
OS Version
2015-04-22
Build Date
2
Countries
2
CSC codes
A (10)
Bootloader binary

Bootloader binary A (10). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Note Pro 12.2 use bootloader binary U (30) (latest: P905XXUBML3). If your device already runs binary U (30), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: P905XXUABOD7
    ModelRegionCSC VersionSizeFile nameDownload
    SM-P905
    AUT Switzerland
    		P905ABOD7 — — Download
    SM-P905
    ITV Italy
    		P905ABOD7 — — Download

    No matching downloads

    How to flash P905XXUABOD7

    • P905XXUABOD7 has bootloader binary A (10). Your device must run binary A (10) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid
    • Display diagonal31 cm (12.2")
    • Display resolution2560 x 1600 pixels
    • Display technologyLCD
    • Processor frequency2.3 GHz
    • Rear camera resolution8 MP
    • Rear camera typeSingle camera
    • Front camera resolution2 MP
    • Wi-Fi standardWi-Fi 5 (802.11ac)
    • Weight753 g

    Frequently Asked Questions

    P905XXUABOD7 is Android 5.0.2 (KitKat) firmware for Samsung Galaxy Note Pro 12.2, released for Italy (ITV), Switzerland (AUT). Samsung built it on 2015-04-22.

    No. A newer build for SM-P905 is available: P905XXUBML3. Install it instead of P905XXUABOD7 unless you need this exact version. The previous build was P905ZSU1BPA3.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Note Pro 12.2 must be on bootloader binary A (10) or lower.

    This build uses bootloader binary A (10). It can be flashed on a Samsung Galaxy Note Pro 12.2 running binary A (10) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 23 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Note Pro 12.2

    No changelog details available.
    Model firmware by region